Models > NGD5240TQ0 Maytag

NGD5240TQ0 Amana Dryer - Overview

Get Parts and Repair Help for NGD5240TQ0

If you know the dryer repair part you need, you can browse the list of all parts on the NGD5240TQ0, or you can search by name or part description. You can also find your part by where it is located on the NGD5240TQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for NGD5240TQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$13.44

Multi Rib Belt - 92-1/4"

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

$17.23

Cycling Thermostat

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees.

$13.95

'M' Series New Style Coil Kit

This gas dryer ignition coil set comes with two ignition coils: one three terminal Boost/Hold coil, and one two terminal secondary coil.

$16.64

Door Switch - 3 Wire

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

$22.31

Igniter Kit

This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 5" wire leads, and the plug. Able to replace both round and flat igniters, this kit is ...

$25.16

Radiant Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

$3.46

Leveling Foot

Sold individually.

$3.83

RING

$13.96

Push-to-Start Switch

This part starts the drying or washing operation.

$18.56

Blower Wheel

The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door switch was bad

  • Customer: pat from lisbon, OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 503 of 504 people found this instruction helpful
i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service read more

dryer would not turn off with door open

  • Customer: RICHARD from NORCROSS GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 409 of 412 people found this instruction helpful
pryed dryer top open and opened front door.. unscrewed the 2 retaining screws. pulled old switch from the wiring harness.
put new switch in place and replaced the retaining screws.
put new switch wire plug into the wiring harness. before closing top, checked door switch function with dryer on.
dryer cut off when door open and when close... read more

intermittant heat

  • Customer: Paul from Monmouth IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 390 of 401 people found this instruction helpful
First I shut off the gas supply and disconnected the dryer vent and unpluged the unit so you can access the rear of the dryer. Then I removed the rear cover. This is where you will find your thermostats and fuses. Holding the new part next to the one to be replaced I transfer the wires one at a time so as not to get them mixed up, then unscrew the old part a... read more