NFW7200TW10 Amana Washer - Instructions

Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

I had to pull the washer out from the wall. SInce it is in front of the door going out into the garage made it dificult getting tools. I had to lay on my side doubled up in order toget to the hose. I used a bit extention so that I could get the clamp loose. Cut the time in half by using a drill with a phillips head screw bit. The only real hard part was getting the new one up tight on the drain. Used a heavy duty screw driver to push it up so the clamp would bite.

My husband simply removed the old sensor and put the new one in. It was not difficult.

Installed dampners with a little trouble because of location on machine. But turned out not to be the problem. Machine still shakes and move. Looking for for another reason for shaking. Replacing dampners would be a "do it yourself project" for most people.

We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

I ordered the pump because we have 3 kids and laundry piles up. The pump was not the issue, because it would drain in rinse, but not during spin... The computer would have been a $330 part. Not sure the issue, but my wife wanted a new dryer so we replaced the washer at the same time. I didn't use the part. The website was really easy to order and it got here fast.

Removed the broker door lever with screwdriver, installed the door lever with screwdriver. Took about 5 minutes.

this is a front load washer, removed a small access plate from the back of the washer, removed the old pump and install the new one

I had noticed the latch on door was split so I ordered the latch, but before I could put it on, the latch on the front of washer was locked. I then looked at the messages from others on this site for help. My daughter and I unscrewed the 2 screws on the top back, removed top, pulled the control panel up, unscrewed the front, unscrewed the 3 screws for latch, pulled old one out. I located the part, ordered it and got it in 2 days! Put new latch in and screwed everything back the way it was and in 15 minutes, the washer is running! (I am a woman too!)

The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.

ND would not empty water end of wash. Empty water from unit. remove back plate replace pump!

It is very easy. Unplug from the wall. Take out the two screws from the back that holds on the top panel. Unscrew the three screws inside the door by the latch. Reach inside the washer from the top and unplug the three plugs on the latch part. Then plug in the new part , put the three screws back in. Then put the top panel on. Plug in and magic. It works!

This took ten minutes .... super easy .... DO IT YOURSELF!!!! About 75.00 with shipping ... can only imagine this woulkd have been 250 to 300 to have somebody com e onsite.

Figured out the part needed to properly fix the problem and when the part came, I was glad I chose the correct one even though I pretty much knew that it was what I needed. I disassembled the door, took the old/broken part out and put the new one. It took about 20 minutes to do it.

Ordered new pump from Parts Select. Pump arrived within 2 days. Removed back cover off washer, 2 screws. Took 2 hoses off pump. Removed pump bracket and pump, 3 bolts. Took less than 2 minutes to remove old pump off bracket and replace new pump. Put everything back together and machine works great and water is out of clothes. Price of pump was the lowest I could find and I couldn't be happier with Parts Select quick response and price.