NFW7200TW10 Amana Washer - Instructions

Coins sheared the impeller blades from the pump. I disconnected the power, removed the back panel, with pliers slide the hose clamp off the hose and remove hose...you will drain water from both hoses when removed (if washer is full of water be prepared for it all to drain)remove 2nd hose clamp and hose, with a 1/2 socket remove the 3 mounting bolts, and disconnect the power line from the pump remove old pump from mounting plate. Install new pump in reverse order.

I went to Maytag.com and typed in my model number and it came up with different parts I found the glass part I needed and ordered it. I received it in like 3 days. I had a phyllips screw driver and it the removal of the base around the glass replace the glass and screwed it right back on and started washing clothes. No leaks at all. I am a woman and proved woman can do the same things a man can do but quicker.LOL

After determining and obtaining replacement part, I used a No.2 Phillips screwdreiver and removed the door and hinge by removing the two flatheat screws that secure the door and hinge to the washer. After removing the screws, the door hinge is still attached to the washer because the hinge assembly has hooks that hold it in place. To physically remove the door, lift up on the door by holding the bottom of the door and the bottom of the hinge and lifting.Lay the door on its face on a solid surface covered by a towel or similar soft cover. Remove all of the screws holding the inside ring to the outside ring. Before removing the inside ring, pay attention top the orientation of the hinge. Lift off the inside ring then the hinge. Be sure to keep the four white plastic caps on the hinge and set the ring and hinge aside. pay attention to the orientation of the glass inside cover and outer plactic cover as it will be easier to reassemble. If you forget, there are notches to realign the glass and plastic. replace the broken outer door ring, lay in the outer plastic cover, the glass cover and the hinge (w/plastic caps). Then reinstall the indise door ring and snug in the screws. Reinstall the door on the washer by inserting the hooks on the hinge into the slots on the washer. Finally reinstall the two flathead screws to secure the door. Your're done.

Of course, before starting any work always make sure your power cord is unplugged to begin with. Move the washing machine to an area with enough room to maneuver around as needed. Now, move around to the back of the washing machine and remove the two Phillip headed screws from the back panel. Push slightly up to pull the two bottom flanges out of their slots. Then pull out on the bottom of the panel which will remove it to allow you access to the inside of the washing machine guts. The drain pump is located directly inside and to the left being held down by three bolts with two hoses running from each side of it. Since there may be a bit of water stored inside the drain pump and hoses have a shop-vac ready to suck up any water that will otherwise go all over the place. If your washer has been down for a while that means sour disgusting mildewed water. Now, unplug the power cord on the top left of the pump and wedge it out of the way making sure it doesn't get wet. Use either a wrench or pliers to remove the three bolts that are holding down the base of the Drain Pump. Remove all of the screws that are holding the Drain Pump to the base. Flip it over to remove the last screw from the bottom. Twist the Drain Pump slightly to move the notches to be able to remove the Drain Pump from the base. Reverse this process to place the new Drain Pump on the base and into the washing machine. If you purchased a Drain Pump with a whole new base already on it then you just have to remove the three bolts and place the new drain and base in. This job is a very easy fix and would have cost you around $300 to $400 dollars having a repair man order the part and come out and do the work. I know because I asked a repair man how much he would charge me for this job. So save your money and fix the easy jobs yourself. Just don't tell my wife it was easy. HaHa!

Removed the front face of washer (broke the plastic pieces on face-no big deal). Had to remove the front housing piece to remove the inner clamp then remove seal. Aligned the new seal up and worked backwards making sure all screws were tightened down. Not super hard, but breaking the plastic pieces wasn't fun.

Removed top cover. Manually opened door through top cover opening. Removed 3 screws at front holding assembly. Removed 3 harnesses attached to assembly. Replaced with new assembly and screwed back in. Replaced harnesses. Certainly an easy DIY job.

Took the two screws out of the access panel on the back of the washer. Drain pump was just inside the access panel. Unplug electrical plug from pump. Take the clamps off the hoses and disconnect hoses. ( Lay towels inside around pump to catch excess water) Take a ratchet, extension, & socket and unscrew bolts from washer base. Unscrew pump from bracket. Put old bracket on the new pump and assemble everything back together opposite of instructions. Very easy fix. Thanks parts select. U saved my family time and a lot of money on repairs.

The product came on time and was perfectly rapped , it took me 15 mins to install after watching you tube videos on front loader washer . I was happy I didn't have to call a service man in . . . .

Very easy repair, once I read the reviews and watched a couple of you tube videos. I just released the band holding the gasket in place, pulled it back, unscrewed the latch and installed a new one. Less than a 10 min job. I am glad I found this web site, thanks guys!!

I simply followed manufacturers direction from the service manual that I had purchased. I removed the cover from the back of the washer, removed the old belt and put the new belt on. The old belt was certainly stretched and putting the new belt on simply required that I walk the new belt on to the pulley and then adjust the belt to the center of the pully. The end result was a washer that now spins as it did when new.

Took both the screws out on the top back. Lifted up the back about 1/2 inch and slid to the back. Reached into the front of the washer where the latch was connected. Disconnected the 3 wires (plugs) attached to the latch, took out the 3 screws located inside the washer door. Took a second person just to hold the latch and bring it out after the screws were off the front inside the washer door. Put new latch in, connected the wires, put in the screws behind the washer door (3 of them) and slid the top into place and put the screws in the back. Takes longer to tell you than to do it. Remember the screw on the left side front (top) as you face the washer and remove that screw. The plastic had disintegrated on mine but am not going to replace that part until I have to.

I read what others wrote and put two and two together and 15 mins. later I was up and running. lots to take apart but it all went smooth and no left over parts washer runs like new again

Purchased the pump from PartSelect after reading other reviews and let me tell you....it works great now. Way cheaper than hiring a repairman.

Took back panel off. Replaced the drain pump

Service repair tech ordered the outside door part and the door safety piece. (plastic shield that covers the glass inside door.) Outside door piece came in within week. Could not get other part in (backordered). Found online and had it within 4 days. Two screws hold hinge on to washer front. After removing hinge screws, pick up on door to clear the tabs on back of hinge through the tab holes in the back hinge brace. (This does not have to be removed. After removing door, unscrewed all screws in back of door to disassemble. Removed hing from hinge slots on door front and inserted into new door hinge slots. Snapped new door safety onto back of new door front by aligning tabs on door safety and outer door piece. Replaced glass bowl and door back by replacing screws in screw holes and tighten. Reattached door by inserting tabs on back of hinge into tabs on washer front and tightening hinge screws.