NED7200TW10 Amana Dryer - Instructions

Callled the service company to diagnose the problem. Watched him take machine apart. He found the problem. Told me the parts that I needed. Didnt know what they were. Went to partselect.com looked my model up and found parts and ordered. Followed same steps as repair guy: Two screws in back of machine then slide top off. Six screws in front to remove front door ( 4 screws on top 2 on bottom) Changed the thermostat and thermistor. Saved 320 dollars :)

Remove dryer covers and locate heater assembly. Removed heater assembly and checked visually if the heater coil is opened, I verified this with an ohm meter. Heater Continuity was OK. Next step I checked the heater sensors. Thermal fuse with bracket had no ohm meter reading between two terminals[open circuit]. Order part#35001193 "thermal fuse" with bracket from "partsSelect.com." Assemble back in reverse order. Please note that the dryer heater was filled with lint and needed a good cleaning.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

First remove the top of this particular dryer, to get to the necessary screws. computer is located on the left side, and 3 screws frees it up. Then disconnect the wires. Unscrew the board, and replace!! That simple!! Unfortunately for me the bad computer melted part of the wire harness. I called maytag and drove them nuts untill they paid to replace the wire harness. I learned two simple lessons. Buy the cheapest appliances you can find because everything is made like crap these days, and if you must buy the more expensive appliances, get the extended warranty because everything is made like crap these days!!!!! Thanks partselect.com for the info, and discount prices!!

top and the front had to be removed to get to the fan... the thermistor that sits in the exaust fan went bad... the heat would come on for a few minutes then turn off completely not getting to clothes dry.....

Had to pull the top off and the front of dryer with a few phillips screws and was able to get to the thermistor and I also replaced the heating coil because it was bad.The cause of the problem was because of a clogged up vent. It was a easy replacement.

had to take top off to get to the front cover screws.Then took the screws out of front cover, pulled it off then pulled the drum out. Man at the amount of lent in the buttom and in the heating element area. Well, after removing drum I found the problem with the pulley. When I got parts to put back together it took a little time and thinking to find out how the pulley an belt went together(belt came off when pulley finally melted in half)with holding drum up to see what's going on. The pulley is laying down,with drum in and belt around it put belt on motor shaft then pull pulley up vertical wrap belt coming down on motor side around pulley. Then put it all together.

The dryer was packed with lint and burnt lint. It was so bad I had to disassemble the entire dryer to fully vacuum it out. Thermostat and thermistor were fairly straight forward. The large wiring harness was difficult. Had to remove the top, control panel, front drum support, blower fan and housing, and finally the rear drum support. I left the old harness on the dryer, and then started around the motor as that was easy to reference in the new wiring harness. I proceeded to remove the old harness, and place the new harness in the retaining clips one clip at a time first moving towards the burner, and then going up the rear of the dryer and finally into the computer board. I had placed groups of screws in very small zip lock bags and labeled them as I took the dryer apart. This helped to remind me where all the screws went when I reassembled. Remember to NOT touch the ignitor with your fingers. Something about the oils on your fingers I was told. Reassemble in reverse order. Rear drum support, motor, gas valve (I had to remove all to clean),Turned the gas on after I reinstalled the gas valve to check for leaks, Drum and belt, attach belt, front drum support, lint trap, front panel/door, and finally the top. Then vent & plug it in and turn it on. Good luck.

Initially I remove the the back panel on the dryer to locate the heating element, but ,next to impossible to remove from this point due to mounting screw located on the blind side of the support bracket.

In order to get to these screw you will have to remove the top of the dryer which is secured with two 10mm screws in the rear. Then remove the control panel secured with four screws.

then I preceded to remove the front of the dryer secured with four screws on the top four screws around the door opening .I gently pull the front open and disconnect the door switch and lift up to remove. I was know able to gain better access to see the screws holding the element housing and support bracket. After removing the three screws I took a picture of the electrical connections for reference which came in handy for reconnection.
The spade connectors are difficult to remove and a flat blade screwdriver works best. Once the element housing is removed from the unit its just a matter of separating the two halves of the housing to gain access to the element itself.

The element is sandwiched between the two halves of the housing and is a bit tricky to reinstall.
It’s best to position the element in the upper portion of the split housing using the four securing screws and then align with the lower half . You then feed the element leads thru the receptacle and bend the securing tabs down and you are ready to reverse the take down procedure..

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Dryer would not start but electronics were working.

Pulled top of dryer off; noticed the belt was loose but not broken.
Went in through the back (1 screw and removed the exhaust pipe/plate); noticed the wheel was broken and thus the belt had fallen off.

Ordered replacement wheel/arm.
One screw to remove old one, one screw to install new one...tentioned the belt. Dryer was good as new.

1. Unplug or turn off circuit breaker to dryer. 2. Remove two screws on the back of dryer that secure the dryer case top. 3. Slide the dryer case top to the rear of dryer and then lift to remove. 4. Electronic Control Board is located in the left side front corner, remove the three screws holding the Control Board and cover. 5. Unplug all wiring from Control Board and remove the one screw holding the board to the metal cover. 6. Reassemble with new Control Board in reverse order. 7. May you be blessed with dry clothes ever after.

This repair is easy. The only drag to this repair is you need to almost completely dismantle the dryer just to get to it. So keep track of your screws.........Look on you tube for videos to dismantle the dryer, you will need to take this down to the drum to change....Once I replaced the pulley, it was about 30 minutes later the dryer was operational again.

Disassembled and tested each part with a multi-meter. Found that the thermostat and fuse were bad. Replaced parts and it is working again.

Excellent. Pulled top cover an exposed the control board. Replaced it just like a piece to a puzzle.