Quick Question!

Have you ever purchased from PartSelect.com before?

Models > NED7200TW

NED7200TW Amana Dryer - Overview

Get Parts and Repair Help for NED7200TW

If you know the dryer repair part you need, you can browse the list of all parts on the NED7200TW, or you can search by name or part description. You can also find your part by where it is located on the NED7200TW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with NED7200TW

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.02

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$31.92

Drum Support Roller with Axle

Sold individually.

$26.25

Thermal Fuse with Bracket

$80.59

Heating Element

This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.

$31.93

Thermistor

This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

$56.45

Lint Filter

This filter collects lint as it passes through the dryer vent.

$6.24

Touch-Up Paint - White

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, ...

$59.31

Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

$22.71

Thermostat

This thermostat helps to regulate the dryer's internal temperature.

$114.68

Heating Element Assembly

This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

A faulty computer

  • Customer: keri from lincoln park, NJ
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 36 of 42 people found this instruction helpful
First remove the top of this particular dryer, to get to the necessary screws. computer is located on the left side, and 3 screws frees it up. Then disconnect the wires. Unscrew the board, and replace!! That simple!! Unfortunately for me the bad computer melted part of the wire harness. I called maytag and drove them nuts untill they paid to replace th... read more

no heat in the dryer

  • Customer: Walter from Lynden, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 39 of 62 people found this instruction helpful
Remove dryer covers and locate heater assembly. Removed heater assembly and checked visually if the heater coil is opened, I verified this with an ohm meter. Heater Continuity was OK. Next step I checked the heater sensors. Thermal fuse with bracket had no ohm meter reading between two terminals[open circuit]. Order part#35001193 "thermal fuse" with bracket ... read more

wet clothes in sensor dry mode(Samsung DV218)

  • Customer: Vincent from Lusby, MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 30 of 44 people found this instruction helpful
top and the front had to be removed to get to the fan... the thermistor that sits in the exaust fan went bad... the heat would come on for a few minutes then turn off completely not getting to clothes dry..... read more