Models > NDE2330AYW > Instructions

NDE2330AYW Amana Dryer - Instructions

All installation instructions for NDE2330AYW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the NDE2330AYW
31-45 of 415
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

very noisey dryer

  • Customer: Mike from El Granada CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 8 people found this instruction helpful
Open bottom panel and observed back left drum roller wheel wobbling and obviously making the loud rumbling banging sound. Search goggle for Amana model part -- found partsellect.com, and read the list of other DIYs:

Take off the lower and upper front panels (two screws
each);

Remove the front drum glide holder (four screws. Careful
here because of the two wires to be removed for
door open off switch;

Pulling drum forward only enough so the bad roller wheel
would come off shaft after removing shaft snap ring
keeper;

Grease new roller hole and old shaft then place the
new wheel roller on shaft;

Replace all items back after cleaning lent off.

Note: Snap ring was a bit tricky (need snap ring pliers)--make sure it is clipped back all the way on the shaft after new wheel is installed. Also, I thought it was a good idea to put something underneath the dryer drum to support it while it was slightly pulled out -- a block of wood, etc. I found a spot remover plastic bottle that wedged up to support the dryer drum enough to take pressure off the belt during wheel replacement.

dryer would tumble but had no heat

  • Customer: Daryl from Pine Island MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 7 of 9 people found this instruction helpful
I opened the front panel and removed the heating element from the rear of the dryer by removing the two screws that held it in place, and slid the element out. using a mulitester I checked the High limit Fuse and it was not working.I ordered the part and replaced it. Everything worked great for two days and the dryer stopped heating again. My brother asked if I had replaced the thermostat because something burned out the fuse. He was right. I ordered both parts and replaced them. Every thing is working just fine. Save some money and time by replacing both parts at the same time.

Broken plastic screen (on frame that holds wire lint screen)

  • Customer: Karen from Homer Glen IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 9 people found this instruction helpful
Removed bottom door panel, four screws. The new part was a slightly different (looks like improved) part, so only had to put two screws back in. Very simple. The only reason it took more than 15 minutes was because I cleaned exposed areas while the panel was off.

Dryer would not require start button to start, and buzzer would only stop after dryer door opened.

  • Customer: Richard from McKinney TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 9 people found this instruction helpful
Disconnect dryer power supply, remove back cover from console, by removing 5screws. Pull out start switch using screwdriver to release plastic locking clips, disconnect wiring harness, reconnect wiring harness to new switch, and slide new switch into the mounting location, allowing the locking clips to engage. Reinstall back console cover, reconnect power supply, and test.

Door safety switch would not close keeping dryer from running

  • Customer: John from Warsaw IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 10 people found this instruction helpful
Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

rumble from drum, hard vibration from drum

  • Customer: Christopher from Severn MD
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 5 of 5 people found this instruction helpful
The parts to replace were mounted to the rear wall of the dryer and only the front pane is removeable. With the panel removed the drum had to be pulled carefully straight out. The belt and tention arm were difficult to reposition. Since you have the appliance apart replace both roller and roller support brackets one of which you cannot see from the front. Throughly vaccum all lint and roller wheel debris . If you have an air compressor take the time to blow out the motor . Make sure to rig a device to hold the tention arm back with the belt correctly aligned while sliding the drum back into place. PARTSLECT is great , easy to use and suggests other parts I may not have thought of and quick . Parts were here in 2 days standard shipping. I was in the dog house for putting this off too long. My wife is happy so I'm happy.

Dryer making a lot of noise and clothes were getting very hot

  • Customer: MedPro from Crest Hill IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench set, Wrench(Adjustable)
  • 6 of 8 people found this instruction helpful
Remove the 2 screws at bottom of front panel, remove lower panel. Then remove the two screws at bottom of front door. Lift door forward so spring hooks can disengage from the top panel. remove door, disconnect the 5 wires to the door latch and light. remove the two screws at top of dryer to lift up top panel. Remove 4 screws at the front holding the drum. Disengage the belt from the tension pulley and remove drum. Replaced both roller wheels at the rear of the drum( one was broke). Then remove the screws (about 6 holding the plate in front of the blower wheel. Use a wrench to hold the nut at the back of the motor and a scocket wrench to remove blower wheel. (The Blower wheel was broken from the shaft and was spinning freely). Then do it all backwards to re assemble. i spent more time cleaning the lint from the inside than I took making the repair!

The dryer started making terrible noises.

  • Customer: Caroline from Rockland ME
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
First I went to Maytag.com thinking it was best to go to the manufacturer for parts. Their search engine did not even recognize my part number. I tried every way I could think of. Then I just entered the model number in google and it sent me to the Partselect.com website. Diagrams came up and I chose parts from the pictures. The parts arrived in about 3 or 4 days and fit perfectly.

Dryer squeaked while running

  • Customer: Robert from Kellogg IA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 5 of 6 people found this instruction helpful
Replaced the recommended drum rollers, belt and tensioner, light bulb. Found repair manual online (bit of a hunt)made job easier still took 2.5 hrs. Then turned drum by hand no squeak. Turned it on and still squeaked. Isolated to motor. Replaced it (had to take dryer completely apart again but went quicker due to experience also had to disassemble the motor assy and rebuild. Took 1.5 hrs works like new now. The design of the dryer is not bad remove bottom front panel first, screws at very bottom of panel then two more screws are uncovered to remove front. It just lifts up and pulls out. then remove four bolts which hold front frame on (supports drum) all this has to be done to reach the replacement parts. drum wheels are held on by snap rings not the screws (real fun if you take them out) reverse to reassemble.

dryer temperatures appear too hot at all settings

  • Customer: David from Crossville TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
removed lower front panel, two screws on bottom edge. Limit thermostat located on lower portion of vertical panel at rear of dryer. I was able to detach the two wires and removed the two thermostate retention screws with a nut driver. Since I could only operate with one hand, I taped the new thermostat in place lining up the screw holes in order to replace the two hex screws. reattached the two wires and front panel.

Dryer would stop during cycle and then not restart. When I started the dryer, there was a short buzz sound as the motor started.

  • Customer: Bob from Denver CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 6 of 9 people found this instruction helpful
First I removed the bottom front cover attached with two screws, then the main front cover attached with two screws. I then removed two more screws holding the top in place, detached three wires and raised the top lid. I held the top lid out of the way with a cord tied off to a cabinet above. I then removed four screws holding the front support panel in place and set it to the side with wires still attahced. Then I slid the dryer belt off the drum and removed the drum. Next I removed the cover of the fan wheel by removing several screws. This allowed me to unscrew the fan wheel (reverse threaded) by anchoring the motor shaft with a wrench and using a large socket to turn the nut end of the fan wheel (then was no snap ring). I then popped off the two clamps holding the motor in place and removed the motor. The only tricky part about assembly was putting the belt back on the pulleys once the drum was installed. You can't see the pulleys once the drum is installed so it is done by feel.

no heat

  • Customer: Janet from Portland OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 5 of 6 people found this instruction helpful
I first removed the two front screws on the front cover located on the lower half of the dryer using a flash light looking on the left side all the way to the back you will see two hex screws removing them will now let you wiggle the heating element back & fourth while pulling down it will come out in just a few seconds - then with your digital camera take a picture of the still wired heating element as to a clear reference for wiring the new element - first Aline the new element in the same direction as the old element and transfer them one by one check camera for assurance that you have done it correctly and re-reinstall in the reverse order

also I would recommend taking off that black plastic blower chute and cleaning it assuringly the best performance of air flow

old latch broke

  • Customer: Jim from Germantown WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 9 people found this instruction helpful
I inserted the clip

Squeaky belt

  • Customer: Michael from Marietta GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removal of the entire 2 front panels
Removal of the heat exchanger into the drum
Removal and replacement of the belt
Reinstallation of the heat exchanger, and both front panels

Noisy and not drying the clothes

  • Customer: Pietro from Fairfax VA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 5 of 6 people found this instruction helpful
This was my first time repairing a dryer. If I knew when I started the project what I know now, it would have been an easy repair. First, you should know that the series number (used for selecting a wiring diagram) is the last two digits of the unit's serial number (not model number). In my case, the series number was 11. The hardest part for me was figuring out how to take the dryer apart. I made the mistake of starting with the top instead of the front. In fact, I removed the control panel and disconnected all the wires, labeling them carefully, and creating a diagram, so i could put it all back together later. I now realize I could have left that all together and just lifted the top up in the front without removing it. That knowledge would have saved hours of work, so I hope it helps someone (prop up the front a few inches and start by removing the panel on the lower front, then remove the screws on the main front panel, and then pull out the bottom of that panel toward you until the top of that front panel disengages from the top of the dryer - the rest is obvious). So it turns out there were two separate problems: 1) the blower wheel had broken completely off of the motor so it wasn't spinning - this is why hot air wasn't being pulled through from the heater in the back of the dryer; 2) the pulley on the spring-loaded lever arm attached to the motor was squeaking due to lack of lubricant. So the solution was to replace the blower wheel and spray WD-40 in the pulley (and also, for good measure in the roller bearings that support the drum in the back of the dryer). Most of the time spent on the repair was just due to my own mistakes. In particular, once I got everything back together after the repair, it stopped squeaking and there was good airflow, but it wasn't heating. I spent an entire day trying to troubleshoot the lack of heat. I tested and bypassed all of the thermostats and heater fuses and the heating element still wouldn't come on. I even managed to accidentally ground one of the leads from the fuse and had to replace a melted wire connector (trip to the Shack). In the end, it turned out that a wire which had been accidentally disconnected from the main power cord to the dryer, I had put back in the wrong spot. There is L1, L2, and neutral going into the dryer. I had the heater on the same circuit as the motor and other stuff. Once I traced the wiring diagram back, I realized this and corrected it by putting the heating circuit back onto L2. Now it "hums like a Singer". If everything had gone smoothly, instead of being a 2-day repair, it would have been a 2 hour repair. 2 hours instead of 1 because to get the leverage I needed to remove the old blower nut, I had to actually pull the motor assembly out of the dryer and move it to my workbench. Someone who is strong or more limber or has better tools might be able to skip that step, reducing the time by about 45 minutes. Good luck!
All Instructions for the NDE2330AYW
31-45 of 415