Models > NBXR463GB1WW

NBXR463GB1WW Hotpoint Dryer - Overview

Get Parts and Repair Help for NBXR463GB1WW

If you know the dryer repair part you need, you can browse the list of all parts on the NBXR463GB1WW, or you can search by name or part description. You can also find your part by where it is located on the NBXR463GB1WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for NBXR463GB1WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.05

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

Order within the next 3 hrs and your part ships today!
$24.57

Front Drum Bearing

Note: The drum slides should also be replaced when your replacing the drum bearing. Slides are NOT included. This part helps your dryer operate as quietly as possible.

Order within the next 3 hrs and your part ships today!
$5.62

Duct Felt Seal

May differ in appearance but functions same as original.

Order within the next 3 hrs and your part ships today!
$4.05

D-Shaped Knob Insert Clip

Sold individually.

Order within the next 3 hrs and your part ships today!
$21.23

Drive Belt

This drive belt is 89.5" long.

Order within the next 3 hrs and your part ships today!
$8.48

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer. The terminal locations on the new switch may be different, match up terminal numbers from old switch to new.

Order within the next 3 hrs and your part ships today!
$48.46

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running...

Order within the next 3 hrs and your part ships today!
$33.18

Lint Filter and Frame

This filter collects lint as it passes through the dryer vent.

Order within the next 3 hrs and your part ships today!
$16.50

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

Order within the next 3 hrs and your part ships today!
$67.72

Lint Trap Duct Assembly

This part includes the duct felt seal (PS9861764) and gasket (PS2577674). NOTE: Per manufacturer this part no longer comes with the sensor bars.

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

original duct was broken

  • Customer: Chad from Gilbert SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 94 of 100 people found this instruction helpful
Dear PartSelect.com,

My repair went off without a hitch.

2 screws removed to remove top.
4 screws removed from inside to remove front panel w/ door.
4 screws removed from top of control panel, loosed and popped top right off.
Flathead screwdriver to pop off old plastic panel.
Removed old wire chase (plastic, approx 3... read more

Drum belt broke

  • Customer: Adrian from Middletown MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 93 of 120 people found this instruction helpful
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on.
This was a first attempt ever at fixing an appliance and it was no big deal. read more

The dryer drum turned ok, but the gas heat did not start.

  • Customer: Gary L. from Freeport IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 70 of 95 people found this instruction helpful
First I found and watched three videos on how to open the dryer and replace the igniter.
Then I opened the dryer, but I did not remove the belt as suggested in the video, and then I removed the ignitor and flame detecter as the videos had shown.
I got on-line and ordered the new parts from PartsSelect in the afternoon and had them in my hands the ... read more