Models
>
NAV8805EWW
NAV8805EWW Amana Washer - Overview
Sections of the NAV8805EWW
[Viewing 7 of 7]Manuals & Care Guides for NAV8805EWW
Click to downloadInstall
Installation Instructions
(0.23MB)
Install
Installation Instructions
(2.60MB)
Manual
Owner's Manuals
(9.32MB)
Manual
Owner's Manuals
(14.15MB)
Keep searches simple, eg. "belt" or "pump".
Drive Belt - 51 inches long
PartSelect #: PS11738882
Manufacturer #: WP21352320
This V-style drive belt measures 51 inches long and 3/8 inches wide. The belt is made to slip on the motor pulley to bring the basket up to the speed required. Continued use can result in the belt suf...
$10.98
In Stock
Lid Hinge
PartSelect #: PS11741780
Manufacturer #: WP35-2044
The lid hinge on your washer is connected to the lid and allows it to open and close. If you find you cannot open or close the lid to your washing machine properly, you may need to replace the lid hin...
$11.18
In Stock
Lid Hinge Pin
PartSelect #: PS11741781
Manufacturer #: WP35-2045
This lid hinge pin allows a washing machine lid to pivot open and closed properly. The hinge pin may need to be replaced if the lid will not open or will not close. The part is white and made of plast...
$22.28
In Stock
Snubber Ring
PartSelect #: PS11738845
Manufacturer #: WP21002026
The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome ass...
$13.11
In Stock
Washer Drain Pump
PartSelect #: PS11741803
Manufacturer #: WP35-6780
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If your machine is not draining properly or if it is noisy and s...
$120.13
In Stock
Transmission Pulley and Bearing Kit
PartSelect #: PS2003651
Manufacturer #: 12002213
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race was...
$69.83
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Motor with Pulley
PartSelect #: PS11738839
Manufacturer #: WP21001950
This motor is a 2 speed, 1/2 HP, 120V, 60Hz.
$163.40
In Stock
Suspension Springs - Kit of 6
PartSelect #: PS2004049
Manufacturer #: 12002773
This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If your washer tub shakes, or moves around a lot durin...
$68.55
In Stock
Screw
PartSelect #: PS11742755
Manufacturer #: WP489483
This screw is sold individually.
$13.09
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Questions And Answers for NAV8805EWW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the NAV8805EWW
[Viewing 10 of 10]Leaking
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
Parts Used:
-
Allen from North Little Rock, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
512 of 515 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump was making a grinding noise
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A
... Read more
small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it.
Read less
Parts Used:
-
Ranse from Layton, UT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Socket set
295 of 317 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The belt and pulley on the drive motor broke
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the
... Read more
base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed.
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
Read less
Parts Used:
-
Michael from Warminster, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
152 of 190 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!