NAV3335AWW Amana Washer - Instructions

Removed front and rear covers, replaced drive belt, tub hose and pump. simple operation. Washer still has some leakage not as bad as original leak. Think I have main tub seal problem. Going to check all hose clamps and run again. If the main seal is problem I will be forced to buy new as the parts cost and difficulty of replacement will be the important factors.

Disconnected hoses and poppped open the top of washer with a flat screw driver from the front. Removed screw holding the water inlet value with a nut driver. Diconnected wires and internal hose from the old valve and attached them to the new valve. Install new valve in place with nut driver. Clossed the top. Reconnected hoses.

First unplugged washer. Found clips on front of machine and lifted the lid back. Took out two 5/16" screws and removed the front panel. Tilted back the washer slightly and took off the drive belt underneath. Started removing the 6 springs with visegrip pliers that support the tub. Then removed the hose on the back left, no pliers needed. Then used pliers to loosen the clip holding the drain hose on the bottom of tub. Moved the clip down, then took off hose. There will be water in the hose, be ready with towel. Watched the video for snubber installation.

Lay the washer on it's side and remove the drive belt. Set back upright. Pry top cover up. Use a small flat bar and try not to damage the porceline. Two hex head screws (one on each side by the tub)holds the frone panel on. Remove those. Panel can now be tilted forward and removed. Pump is on right side. remove the two hoses and save the clamps. remove the three hex head screws holding the pump. Install the new pump and reassemble. Pretty easy.

it is best to watch the video before doing this reapir. Once you see that the job is straight forward, making sure not to remove all of the spring screws is very important.

tilted washer about 45 degrees off with old on with new belt.TOO easy

After inspecting the brake and installing the new pulley/bearing kit the washer still would only spin slowly. Discovered that if the washer agitates at all in the spin cycle then the transmission is shot. So washer was replaced with a new one.

Watch the videos on it about replacing the snubber ring. Do not remove the whole assembly just loosen enough to get old snubber out and new one in, or you will find it very difficult to get the brake/clutch assembly back together Also I used a 2 x 4 scrap to push and hold the the barrel while removing the six springs. Wear long sleeves as the metal on the washing machine panels will cut you very easily. Belt was just sliding it over the pulley. One other recommendation is take a pictures before and while you are taking it apart for verification of reassembly.

Followed your excellent video instructions to change out the motor.

Very easy pop-ed up the top from front used my Duroc screw driver removed screw removed lid slid hinge on slid lid back in place attached screw. Make sure you get screw tighten and snug. Job Done!

put a total new transmission total kit on.

Opened back panel. With pliers, moved the retainer clamps. Used a flat screwdriver to pry off hose from tank. procceded to remove hose from pump. Put new hose on and replaced hose clamps. Tested with a small wash cycle, no leaks. Job done.

I was struggling for more than an hour trying to put the E clip on with the thicker washer as recommended then gave it up. I tried again with the thinner washer and still can not get the clip fully seated in place (only one end got into the groove). Frustrated, I decided to tap the other end with flat screw driver and hammer. The clip seems to be deformed but rested in the groove. Checked the brake adjustment and it was on the min mark. I did not dare to remove it for adjustment, and there is no thinner washer to adjust anyway. The washer is still working OK now after 3 loads. Other than that I am really happy with the purchase. Supper fast shipping. Very helpful instruction video. Only I am not really a handy man as my wife often encourages!

Unplug machine shut water off 1 remove drive belt 2 remove 2 hose's with pliers and 3 use 5/16s nut driver for the 3 screws on the pump. And just the reverse to install it works great now Good Luck

I'm glad I found this website, it saved me from buying a new washer. Many other people had the same problem and I used the two top parts from the symptoms chart, and it fixed the problem. I'm sure it was the pump making the noise, but I decided to replace the belt also. Repair took less than 30 minutes.