Models > MZD2665HEB > Instructions

MZD2665HEB Maytag Refrigerator - Instructions

All installation instructions for MZD2665HEB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MZD2665HEB
526-540 of 682
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice maker stopped making ice.

  • Customer: Brenda from Stoneham, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I followed the instructions from your video. I did this replacement all by myself. I am a 64 year old woman and have never done anything like this before. It could not have been any easier.

Refrigerator Warm Freezer Cold

  • Customer: jim from bush, LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Cleaned out freezer and unpluged the frig to let ice melt. Removed the shelves from the freezer and took screws out of back bottom panel on inside of freezer. Panels pulls up and can be removed. Had to disconnect light that is attached to panel. Unplugged the old heater element and removed it. Also removed the thermostat. There is not as much room as shown on the model in the video so it takes care and patience to remove the old one and install the new one. Also the new thermostat will come not wired to the heater element as shown in the video so be prepared to connect the wires. Really an easy over all job and not the unit works perfect again. All together I spent about 180. 00 And if I had bought the right parts the first time it would have only been about 80. 00.

Water running into ice bin and freezing

  • Customer: Frank from Greenwich, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced icemaker and used wire harnnes and plastic cover off old one. Real easy!!

Change Ice Maker/ Water Fill Cup

  • Customer: allen from holland, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The ice maker change out was easy. The problem was the part came with a different filler cup but the one needed was supplied. Changing to the other cup required taking the ice maker apart and installing the other filler cup. Go to the parts list and find the filler cup. Use instructions found there to change to other cup and then install your ice maker.

no ice.

  • Customer: corey from des moines, IA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Changed the ice unit. Found it was not the problem. Then I changed the solenoid that dispenses water to the ice maker. That is what was defective.

Ice is flowing again

  • Customer: David from Burkburnett, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
My Maytag side by side had stopped making ice suddenly. My wife loves her ice. We were at a loss until we found the Parts Select website. I ordered the new icemaker and the dual water valve. After watching the short installation videos I changed the parts on my refrigerator and in about 45 minutes I heard the sound of ice dropping into the bucket. With the wide selection of part and easy to understand videos we had Ice and my wife was happy. I recommend this site to anyone that wants to repair a malfunctioning appliance

Water filter needed to be changed

  • Customer: Cathy from San Pedro, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Piece of cake. Took out old filer and put in new one!

The bottom freezer and the fridge stopped cooling what seemed at a random time but was also after an electrical storm.

  • Customer: Cassondra from Dallas, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First off I had no idea how a fridge worked or where to begin and the troubleshooting section of the manual was a joke. So I took the back panel off made sure the coils underneath were clean. Took out the back panel of the freezer and made sure that nothing was frozen over and I hadn't seen excess water on the floor so ruled that out. I knew the condenser was still running so I took a shot in the dark. Ordered the part and waited for it to arrive. It took me 3 minutes to open the box and install it. Immediately knew it was working replaced the back panel and moved the fridge back.

The refrigerator side is not cold enough while the freezer side has ice and frost buildups

  • Customer: Tito from Pearland, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I went online to diagnose the symptom and 3 things came up, thermostat, heater and adaptive control. I replaced the thermostat but the symptom continued so I also replaced the heater. This fix the problem. On the front side inside the freezer, take out the panel by removing everything (food, tray). The panel can be removed by using a nutdriver. Once the panel is removed, you can see the ice on the evaporator coil. You can wait or use a hair dryer to melt it. Get ready to collect the water from the rear of the fridge by opening up the rear bottom panel and using a scoop (I used a cough syrup cup)to collect water from a very shallow drip pan. If you don't scoop the water out, it will spill on the floor once the ice have all melted. The coil is attached to the fridge body by 2 plastic tabs. I pulled the coil near the tab to minimize pressure so that you wont misshape the coil. I broke one in the process but I do not see the need to replace the broken tab. When I put the coil back, it was still firmly in place. The heater is at the bottom of the coil and is attached by 2 wire clips. Very easy to remove using a plier. There is not much room to move the coil because it is attached to the refrigerant line. Using a plier, you have to open up the side of the casing where the coil sits so that you can take the coil straight out. Reverse the process to finish installation.

Leaking Valve

  • Customer: THOMAS from PETERSBURG, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Removed plate from back of fridge,removed water lines, removed valve from plate, put new valve on, reconnect hoses, reinstall plate.

Filter Needed Replacement

  • Customer: ROY from SOMERSET, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Opened filter area door turned old filter to the left to unscrew. Took out old filter then replaced the new filter and turned it to the right to tighten it, closed cover and that was it all done.

Light switch was broken off.

  • Customer: Melodie from Gouverneur, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Purchased the new light switch, used a butter knife to pop the old one out, used the pliers to pull the wires off the metal tabs, replaced the new one with no problem. Took about under 1 minute. Lights are now all working.

Part came in as Maytag not whilpool

  • Customer: Chris from Oxnard, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Called service numbr and they said they were the same company- Part would fit.

Ice buildup in icemaker inlet tube

  • Customer: Mark from Valatie, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Probably a result of hard water. Valve did not close down completely after ice making cycle. Video made job easy just make sure plastic hoses are in all the way. Problem solved.

icemaker leaking water into ice tray

  • Customer: Sidney from El Paso, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
removed old icemaker and transfer some of the parts to the new icemaker. The only problem was that I had to disasemable the new icemaker to replace the fill tray with the older style (which was included). Once that was done, installation was pretty easy.
All Instructions for the MZD2665HEB
526-540 of 682