MZD2665HEB Maytag Refrigerator - Instructions

Freezer would get cold at bottom and some of the refrigerator. Took of freezer back panel and located freezer fan. Took a meter and saw power was getting to it, but not working. Removed fan and replaced with new on, working like a charm. Cold air was not circulating enough throughout the unit because fan was not working. It was not the thermostat or adapter control.

I removed the plastic cover from the top hinge and loosened the screws. The magnet seal kept the door in place so I removed the top hinge and tried to lift the door off the bottom hinge but the water line wouldn't let it go. Since I don't use the water feature, I just cut the water line and lifted the door off. That's when I discovered the hinge pin was actually broken off, not just the cam. I went ahead and replaced the cam kit and put it temporarily back together, got right back on line and ordered the bottom hinge. The service was again very fast and in a couple of days I received the bottom hinge, repeated the whole process again and this time replaced the bottom hinge assembly, put some petrolium jelly on the cam kit and now it works smooth and perfect.

I pulled the whole unit(condenser&overload relay)
with my hand & disconnected the wire connected
to it & Replaced it with the new one.Peace of cake.

Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.

Remove bottom panel in freezer side to get access to the coil.Remove old heater element and defrost thermostat.Installed new hearter and thermostat.Screw back bottom panel re-start frige.

Thanks to parts.com showing the schematic the repair was very easy. Note if the buttons fro dispensing water/ice break you need to order two parts. 1. dispenser Facade and 2. Dispenser facade Insert. To replace do the following. remove the catch tray at the bottom of facade. remove the two screws on the bottom and gently pull bottom of insert out and down. Next unsnap the two wires on the selonoid switch. Next pull down on the harness connector from the printed ckt. Next remove small phillips screw that secures the ckt to the insert and gently pry the six plastic clips that hold the ckt to the insert and remove. Next, install the ckt into the new insert and reconnect the selonoid switch. Next, install the insert back on the door. Next, install the Dispensor Facade sticker over the switch buttons taking care that it is aligned properly. Thats it ready to use.

Turned the old one to unseat and replaced with a new one in the reverse order.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

Cut wires and removed old thermosat. Spliced new thermostat wires into exsiting wire. Put it all back together. Works great now. Thanks for all the help. Your site is great. Only problem we had was getting the part from FED EX. Took over 2 weeks had to go pick up the part ourselfs.

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

Refrigerator was stored for about 2 years and we picked it up when the owner decided to move into an apartment and no longer needed to unit (lost home to foreclosure). Brought the unit home and it worked great for about 3 days. On the third day my wife noticed a slight electrical burning smell. I did also and quickly emptied the unit and hoped for the best. The unit did indeed stop working. I fancy myself a do it myselfer but I would normally not go near electricity but thought what the heck it was free if i ruin it I would give it away. After a little research i found Partselect and they had a great design and a few stories that sounded similar so i pulled the relay capacitor for the compressor and sure enough the unit showed burn marks where the unit had shorted out. Maybe a bug got in there or water, dirt but I ordered the part. I arrived in two days which was great. I installed the part and plug the unit in and crossed my fingers. Very happily the unit clicked on and has been running great ever since. thanks Partselect, while I may not be one of your big customers I will refer anyone with appliance issues to your site first.

Followed the first set of instructions from the parts select website. It worked perfectly. Just note that the way to remove the "blue" tube is by pushing down on the fitting and then pull the tube out. Be careful with the styrofoam piece around the hole for the tubes as it can crumble around the edges.

remove the bin from the freezer, there are 2 tabs on the lower front cover that pop off and you just pull the entire front cover off. there are 4 nuts that hold the blade cover which you can use the 7in1 with the insert removed.. i believe it's 5/16". remove the cover and the tumbler assembly pops out of the tray.
remove the nut with a set of pliers and lay it out on the table in order.
install is reverse of removal. make sure you get all the washers in the correct location when assembling. don't tighten the nut too tight or it will bind the rotating assembly.

enjoy retrieving ice from the door again!

Removed the filter from inside the ref then disconneted the water line to filter and to ice maker on blue line just push line down then up to remove. Then pull whole assb. thru refreg. and install new one. very easy 2nd time mine went bad 1st time it coast almost $300.00 this time less than $50.00. Take your time and its fool proof.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt