Models > MWD366 > Instructions

MWD366 Maytag - Instructions

Installation Instructions for parts on models starting with MWD366

These instructions have been submitted by other PartSelect customers and can help guide you through the repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with MWD366

All Instructions for models starting with MWD366
1-9 of 9
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burned out light bulbs in microwave hood stove

  • Customer: Herbert from Norton MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
I had some difficulty removing the glass plate because of the awkward (upside down) position of the screw that retained it. After replacing the burned out bulbs and replacig the glass plate the problem of replacing the screw involved my dropping the thing several times before I got the screw threads to catch. I got a screw thread to catch enough to hold the glass plate in position and left it at that.

burned out bulb

  • Customer: john from plainfield IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
removed two screws,lowered the glass shield,removed the burned out bulb and replaced it with the new one. I ordered the bulb from parts select and recieved it two days later. It was a pleasure to deal with them, and certainly use them again.

light bulb burned-out

  • Customer: Pablo from Burlingame CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 13 people found this instruction helpful
screwed in new bulb

Microwave would not heat food. All other functionality was working as expected

  • Customer: James from Staten Island NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
I disconnected the power. Took off the front panel that was held together by two screws. Reviewed the schematic that was inside. Located the switches, saw which lead was burnt. Unscrewed the two screws that held the switch in place, cleaned the connector, and put the switch in and connectors back. Powered the device, tested for cooking/heating functionality. It worked, Closed the front panel

BURNT OUT LIGHT BULB REPLACEMENT

  • Customer: alfred from summerville SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 16 people found this instruction helpful
OPEN COMPARTMENT, INSTALLED BULB, CLOSED COMPARTMENT

Replacement of hood light bulbs

  • Customer: Jerry from Pine CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together

2 burned out bulbs under the microwave/important light source for kitchen stove.

  • Customer: Ferol from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

Burned out light bulb

  • Customer: Ray from Gatlinburg TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced light bulb.

replace light blub

  • Customer: roger from palm coast FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.
All Instructions for models starting with MWD366
1-9 of 9