The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
These parts are the replacement suspension rod supports for your washer. They are made of plastic and are approximately 1 ½ inches in diameter. This package will come with an 8-piece set of suspension...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
$7.97
In Stock
Questions And Answers for MVWX700XL2
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
8 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mickie
July 21, 2021
How do I remove the dispenser tray
For model number MVWX700XL2
Hello Mickie, Thank you for the question. You will need to pull the tray out as far as it goes and then tilt the front upwards to release the back to remove. We hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Doug
January 27, 2020
Spins crazy. Are there springs balancing the drum
For model number MVWX700XL2
Hi Doug. There is the suspension part number PS11703291 along with spring PS3497596. Thank you for your question and good luck with your repair.
Do I remove the dispenser tray when I use powdered detergent? If so, how?
For model number MVWX700XL2
Hello Mickie, Thank you for contacting PartSelect.com. Very sorry but we do not have the use and care information of the appliance, just parts lists and diagrams. For more specialized assistance or to speak with someone about this, we would suggest calling Maytag directly. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Beverly
January 4, 2020
Washer timer seems to be off and sometimes the lock switch cuts on and off
For model number MVWX700XL2
Hello Beverly and thank you for writing.
It certainly sounds like it could be a faulty switch latch PS3497627, you should check for signs of damage, and replace if necessary. We hope this helps. Please contact us anytime.
Washer runs through whole cycle but will not spin, i changed shift sensor,still does not spin, could the problem be the lid switch?
For model number MVWX700XL2
Hi Bryan,
Thank you for your question. If your washer is not spinning, there are some parts that you will need to check to see which one is causing the issue. You will need to check shift actuator, the drive belt, the lid latch assembly, the washer drive pulley and the drive hub. We hope this helps! Good luck with the repair!
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer faile
... Read mored which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read moreation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
