This kit includes one driver hub and two driven basket hubs. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced.
$37.73
In Stock
Order within the next 12 mins and your part ships today!
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Order within the next 12 mins and your part ships today!
These parts are the replacement suspension rod supports for your washer. They are made of plastic and are approximately 1 ½ inches in diameter. This package will come with an 8-piece set of suspension...
$6.88
In Stock
Order within the next 12 mins and your part ships today!
This part makes sure that the lid is shut before allowing the machine to start or agitate.
NOTE: This is a manufacturer substitution. Part may differ in appearance but is a functional equivalent to prior parts including
$94.96
In Stock
Order within the next 12 mins and your part ships today!
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Order within the next 12 mins and your part ships today!
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Order within the next 12 mins and your part ships today!
This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. Customers have rated this repair as easy. To c...
$43.95
In Stock
Order within the next 12 mins and your part ships today!
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
$22.68
In Stock
Order within the next 12 mins and your part ships today!
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$152.28
In Stock
Order within the next 12 mins and your part ships today!
Questions And Answers for MVWB850YW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
March 22, 2022
Replaced the bearings on mvwb85yw0 and the basket hub is 1/4 inch away from meeting up with the basket. I measured the old parts to see how far the shaft should be sticking up and it seams to be correct.
For model number MVWB850YW0
Hello John, thank you for writing. We do not show bearings on the parts list. However, we do see a Basket Hub Kit part PS11723155. This kit includes one driver hub and two driven basket hubs. The basket hub is located under the agitator. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Hi Jose, thank you for contacting us. If your washer has a vibration, seems to "walk" across the floor, has a thumping or banging noise, or seems off-balance, there may be an issue with the installation, or with the items you are washing. The front and rear feet must be in firm contact with the floor, and the washer must be level to operate correctly. Grip washer from top and rock back and forth, making sure all four feet are firmly on the floor. Repeat, rocking the washer from side to side. If the washer rocks, adjust the leveling feet. If all four feet are in firm contact with the floor, tighten the jam nuts against the base of the washer. Jam nuts must be tight against the bottom of the cabinet. If the washer is installed with a pedestal, ensure the mounting screws are tight, and the pedestal's feet are in firm contact with the floor, and the foot lock nut is tight to the frame. The washer must be level, or it will vibrate. Check the floor for flexing or sagging. Do not install the appliance on a raised wooden platform or a carpeted surface. Let us know if you have further questions!
Was this helpful?
Thank you for voting!
Mary
June 7, 2023
I have a broken knob that needs replaced.
For model number MVWB850YW0
Hi Mary, thank you for reaching out. The compatible knob for your model is part number PS11753161. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you!
I replaced the suspension rods, but it still has a little balance problem on the spin cycle. Not as much as before the new rods, but a little. Could there be another problem
For model number MVWB850YW0
Hello Robert, thank you for reaching out. According to our research, you may need to check that the load is evenly distributed. If you don't balance the load, the washer will become unbalanced during the cycle. If the issue still occurs, you may need to check that leveling leg, part number PS11753762, to level the washer. We hope this helps!
Hello Dan, thank you for your question. We have an installation video for the lid switch that will show you how to remove the top. You can find this video by searching the lid switch part number PS11756782. I hope this helps.
Removed a cap in the center of the tub basket which has a bolt that needs removed I believe it's a 9/16 after I removed the bolt I then removed the center of the bottom of the basket assembly which then allowed me to get to the basket hub that needed replaced it was a little dirty and I couldn't get it out so I sprayed a little penitratin
... Read moreg oil on it let it sit a little then I was able to remove the hub and install the new one then I put it all back together and the washer is working great
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
