Models > MVH350W (P1323207M) > Instructions

MVH350W (P1323207M) Amana Microwave - Instructions

All installation instructions for MVH350W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MVH350W
46-60 of 67
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Turntable roller guide broke

  • Customer: Michael from Englewood CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled out broken roller guide, replaced it with new one. It was just that easy.

Needed a new bulb under the microwave.

  • Customer: Norma from Unionville MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

turntable platform broke

  • Customer: Rex from Mount Sidney VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Dropped in the new one. Took about 30 seconds.

Replacement of hood light bulbs

  • Customer: Jerry from Pine CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together

Our turntable broke and wouldn't rotate

  • Customer: Mark from Seattle WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The turntable wouldn't rotate any more. The problem was the plastic roller guide (under the turntable glass) had cracked where it attached to the shaft. I installed the new part, it fit perfectly, now works great!

TOO BIG DIDn' FIX

  • Customer: BRIGIDA from GAINESVILLE VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
i RECEIVED MY GLASS COOKING TRAY SO FAST BUT WHEN I TRY TO PUT IN THE MICROWAVE DID't fix was to big,i call you today to return and very nice lady help me and told me i need to call whirlpool and explain them and already order again thank so much for all your help you have very nice people in customer service. THANK YOU SO MUCH AGAIN. !!

The turntable in my microwave quit moving

  • Customer: Janita from Andover MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Opened the package and inserted the turntable roller guide. It was the right one and worked immediately!

Microwave worked intermittently

  • Customer: Robert from Palmer Lake CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The door was not engaging the micro switches properly no doubt from 10+ years of wear. The upper switch removed fairly easily but take care not to tweak the plastic brace too much or it will snap. The lower one was the tricky one. After much examination I noticed that the trick to remove it was underneath the brace. Take a butter knife (no joke) and insert it just under the old micro switch and gently press down twisting the micro switch every so slightly til it releases. The replacements snap back in with no trouble. The microwave is working much better now, though not perfect.

one of the rollers broke

  • Customer: Jesse from San Jose CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replace old part with one one ordered from PartSelect

2 burned out bulbs under the microwave/important light source for kitchen stove.

  • Customer: Ferol from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

Motor quit working but light and timer still worked.

  • Customer: Thais from La Grange TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

Missing wheel on turntable

  • Customer: Laura Faye from Checotah OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy! Just place it in the slot inside the microwave.Finished! Tah Dah!

Burned out light bulb

  • Customer: Ray from Gatlinburg TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced light bulb.

Original seal tape had released and the glass was very dirty

  • Customer: Sharon from FOLLY BEACH SC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the old seal tape, took the door apart and cleaned the glass. Put the door back together and replaced the seal tape with the new seal and it looks like new. Watched a video on line on how to take apart the microwave door and it was very easy.

motor would start by itself when door closed

  • Customer: Lewis from Loveland CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
remove 4 screws from top, front louvered panel snaps out. remove 1 screw from top of keypad, keypad pivot's forward and can be removed. There is a white mounting bracket inside left. Remove two screws, one top and one bottom, bracket lifts up and out. 3 sets wires are attached, mark them with masking tape, top, center, bottom and pull out plugs. They can only attach one way. Using a very small screw tip, lift plastic latch from switch, it rotates out and is removed from the pivot pin. reassemble in reverse order after switches are replaced
All Instructions for the MVH350W
46-60 of 67