Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MVH250E (P1323203M) > Instructions

MVH250E (P1323203M) Amana Microwave - Instructions

All installation instructions for MVH250E parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MVH250E
16-30 of 64
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

burned out bulb

  • Customer: john from plainfield, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 16 of 23 people found this instruction helpful
removed two screws,lowered the glass shield,removed the burned out bulb and replaced it with the new one. I ordered the bulb from parts select and recieved it two days later. It was a pleasure to deal with them, and certainly use them again.

Close the door on the microwave, punch in the # nothing happened

  • Customer: Robert S. from Stafford, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 13 of 18 people found this instruction helpful
I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.

microve stopped working

  • Customer: Denice from Montgomery, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 10 of 16 people found this instruction helpful
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

latch was on microwave door

  • Customer: william from lithonia, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 10 of 17 people found this instruction helpful
Had to remove door. Next pop off the plastic trim around door. Remove spring holding latch place new latch and afix it to the door frame

Died while heating lasagna

  • Customer: connie from madison, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 15 people found this instruction helpful
Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

Fan motor and magnetron did not come on, but every thing else did.

  • Customer: Dale from Chester, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
Problem would come and go. Found service schematic inside unit. Perform all the suggested tests. One possible solution was the primary interlock switch shown on the schematic and a check found the switch stuck. It would free up some times but would stick again in the open position. Ordered switch which was a simple plug in unit.

Needed to push door up to run appliance.

  • Customer: J Patrick from Baltimore, MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 22 people found this instruction helpful
1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but broke plastic retaining clip despite every effort not to do so. Reset broken clip with super glue. 5. Reassembled cabinet and appliance is in good working condition.

burnt out bulb

  • Customer: THOMAS from STOW, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 47 people found this instruction helpful
took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

Turn table in the Micro was broken due to the plastic 3 wheel mechanism that cracked. t

  • Customer: Cesa Lynn from Montgomery, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
I could just set the new whirly gig in the bottom hole of the micro and it worked. The new part was delivered in 24 hours of my order and hence fixed in 24 hours. Thanks so much Part Select

Old roller piece broken

  • Customer: Jack from Scottsboro,, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
Took out the old, put in the new.

My turntable wouldn't turn

  • Customer: Yvette from Riverdale, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
I took the turntable roller guide, dropped it into the hole, put the plate back on the turntable roller guide; and voila!!! It worked!

Plastic latch to lock the microwave door broke.

  • Customer: Richard from Arlington, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 14 people found this instruction helpful
Did an online search for repairs and found PartSelect. Simple to order the part and had it installed myself less than a week later. Thank you!!

original rotater broke

  • Customer: Cynthia from Wylie, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
Replaced the broken piece with the one purchased at Partselect.com. I was concerned that the part would not be correct since all we did was enter the model number of the microwave. PartSelect.com was really easy to use and sent the correct part. Thanks so much for making this process easy.

light bulb burned-out

  • Customer: Pablo from Burlingame, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 21 people found this instruction helpful
screwed in new bulb

Stem broken off the turntable base so the turntable wouldn't rotate

  • Customer: Joellyn from Olathe, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Removed the broken plastic base that the glass turntable sets on and put in the new plastic base. Took 5 seconds max! The part arrived in about 24 hours! Great service!
All Instructions for the MVH250E
16-30 of 64