MSD2651HEW Maytag Refrigerator - Instructions

Went very well. I replaced the ice maker itself cause of the high failure rate but that did not fix it. Measured voltage across water solenoid and it was around 1 volt. Measured the voltage at the water solenoid for ice and it was 20 volts. This was measured when it was plugged in. So I replaced the valve took 15-20 minutes including moving the fridge out. Started making ice 8 minutes later.

removed old water head valve and replaced with the new one.

Couldn't believe how complicated this part is with heaters. It is used in at least a billion refrigerators and functions well. But I had to tear it all apart to adopt it. Got it all done and stayed awake all night for waiting for Ice. Nothing! Then a Erika moment! Turn the ice arm full switch off! Then Ice poured out every hour. Expecting many years of ice. Thanks for speedy delivery especially before Christmas..

need instr. to repair

Pull the refrigerator forward take off the back panel and replace valve seem valve leaking

The repair was a lot easier than I thought. I first ordered the ice-maker part from PartSelect. Followed the instructions from the how-to video and I was done within 30 minutes. Unplugged the fridge, took out the two 1/4" nut screws holding up the ice-maker, disconnected the wiring harness and then re-attached the new ice-maker in reverse order. Had to use some of the parts from the old ice-maker, like the cover, ice wire (the wire that moves up and down, letting you know when the ice box was full or starts the ice-making process) The whole process along the PartSelect video made it easy.

Watch the video and then do the repair.

take the front off the ice maker. take the bar out. then replace the helix end cap. then put the bar back and the front.

My husband took the door off and replaced the door closure cam kit with no problem the door opens without a sound.

First of all, I do not consider myself very handy. Most of my simple home repair projects include at least 2 trips to the local hardware store and take twice as long as they probably should. So if I can do this anyone can. For once, rather than just blindly throw new parts at a problem I did check the water pressure to the icemaker first and then even tested the icemaker with a multi-tester to determine what was wrong. I had $5.00 mulit-tester in my workbench but had never actually used it before, so I found step by step instructions on another website on how to test the motor and it turned out that one of the circuits in the main motor was in fact bad. Since the motor was around $80.00 dollars and the Whole unit that's inside your freezer is about $120.00 I decided it was best to just go ahead and replace the entire unit rather than just the motor. From what I saw online normally replacing an Ice maker is fairly simple. Remove 3 screws swap the prewired plug along with the metal arm then just reinstall it. Somehow whenever I try a home repair it's never that simple. First of all, our freezer is on the bottom so removing the screws holding the ice maker meant that I had to climb over, around and under the freezer shelves in order to get to the ice maker itself. Also one of the screws is not visible from the front so I had to hold a mirror in one hand while I tried loosening the screw with the other. Since the metal arm that turns off the ice maker is not included in the replacement it had to be moved over. Of course it was stuck, so it did take a little time to get it loose because I was being careful not to bend it and have to order another one. Finally installing the new icemaker meant once again that i was climbing over under and around the basket in the bottom level freezer. There is probably an easy way to remove the entire drawer but I couldn't find the release tabs so when just pulling harder on the drawer didn't work, I thought it best to just work around it. Still all in all, not a difficult job, just a little time consuming. The guy in the video did the swap in about 6 minutes, it took me about 45.

Installation was really easy since the replacement part was identical to the OEM part. Removed the three mounting screws with a nut driver. This allows one to remove the icemaker from the wall and disconnect the wire harness plug from the icemaker. I never unplugged the harness from the rear wall of the refrigerator. Put the new icemaker in place, making sure to place the water fill tube in the proper hole. Plugged the wire harness into the new icemaker and tightened the three mounting screws. The icemaker worked perfectly from then on with clean ice cubes and no leaks.

Unplugged appliance. Using a small putty knife I moved the switch out far enough to grab it with pliers. Moved wiring to new switch and pushed into place after testing.

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

The part is a heavy plastic-like decal, basically. The old one peeled off, slowly. A fair amount of glue was left behind. Cleaned the surface of the button area, to remove old glue. (alcohol didn't work so well, use a crayon remover product. Should probably test surface before use). After cleaning, removed backing of new façade-decal and carefully aligned, and applied, smoothing out any air bubbles under surface.

This part was very easy to replace. Actual time to remove the tubing and wiring harness and then replace and reinstall tubing and wiring was probably less than 3 minutes. Just be sure to mark each tubing prior to removing so you can reinstall in the correct fitting. In my case, the most difficult and time consuming task was removing the refridgerator rear access panel because I had to do all this through the motorhome exterior access panel which is probably about 10" by 10". Replacing the actual valve was very simple. Quick shipping too to our campground.