MSD2542VEB00 Maytag Refrigerator - Instructions

removed three screws

The repair (really replacement) took less than 2 minutes. You press a button to pop out the old filter and stick the new one in. Easy as pie.

First I called Mr appliance from Bayport ny, And they told me we needed a new frig. So that night we went out and bought a new one from PC.The next day I canceled it and watched your video. The freezer side was cold and the fan was running so I figured it was most likely the defrost timer or the bimetel thermostat as the evaporator was frozen.I ordered the part from you (parts select)installed it EASY And it runs perfect!! This is my second time the last time it was my Moms frig but in this case the fan was not running. So I ordered from you watched your video and again it runs perfect. Thank you for all your help. I will always order from you.Oh and the part was at my door in two days.And I was able to cancel the other frig 1300.00 saved Thank you parts select

Had to Test Seloind. It Was OK. Then tested Motor Motor For Ice Maker. It Was Bad. Went Online Looked Up Parts For My Unit. They Were Shipped in a Timely Manner, only a few days. Installed parts in less than 15 minutes. Went very easy. Thank You

According to all the information on the internet diagnosing the problem with my in door ice dispenser, the problem seemed to be with the solenoid which I ordered from PartSelect. However, when I got into the repair, I found the problem was with the electrical switch that activated the ice dispenser. A couple of the plastic studs that hold the switch in place had broken which did not allow the switch to be activated. I replaced the small plastic keeper study with small screws and now the ice dispenser works fine.

The retaining pins, which are part of the control bracket, that hold the micro switch that powers on the ice dispensor had broken, allowing the micro switch to fall away from actuator paddle. I replace the entire control bracket which holds the 2 micro switches, one for ice dispensing and one for water.

Ordered new glass shelf installed it.

I removed the outside ice door panel with two flat head screw drivers inserted in the slots at the bottom of the panel. You simply pry out until the bottom releases and then you push it up gently to release the top. I then removed the hex head screws that held the outside wire panel and the switches, at this time you need to remove the old plunger that is connected to the top of the ice door assembly. I then disconnected the old heat strip and removed the hex screw that held the ice chute at the bottom. Then I removed the pin and spring that held the ice door assembly at the top. Replaced the parts with new ones provided in the kit. The ice door is no longer freezing up, nor is the ice bucket in the freezer. The freezer is now back to the right temperature, without having to be set on high

Took the part out of the package and installed it. The service I received was excelent. Got the part two days after ordering it

I would never attempt an appliance repair but after watching the video instructions for installing this part I decided to give it a try even though I'm dangerous with a screwdriver. After retrieving a nutdriver from my $39 handy dandy tool set, it was a piece of cake. Upper hinge cover, hinge, door removal, comes off in a matter of minutes. Only problem surfaced when I went to install my new cam in the lower hinge. It didn't fit. It was actually for the upper door hinge. I reinstalled the lower plastic piece (whatever it's called), tightened it down, put the door back on (you can do it yourself if it's the refrig. side) and popping sound was gone. I guess the bottom hinge plastic piece was probably loose but you can't tighten it unless you remove the door. I now have a upper door cam in my drawer ready when it fails and will replace it without hesitation.

No instructions with part. Found a picture on line and changed the arm, but it didn't fix the problem. Fairly easy after figured out what needed to be done to get to the part.

Did it entirely by myself while my husband was at work

Took off all screws on box.Removed front of drawer,removed back-up to drawer and auger as one unit. Removed C-clamp on end of auger,this released all the parts. The end of the auger shaft unscrews, remove broken piece and reverse process with new part

I cracked the crisper pan after having the refrigerator only one week and needed a replacement ASAP!! I was so happy to find this site and the part I needed. It's a little pricy for a plastic drawer but I can overlook that since it was in stock and I received it the very next day!!!I took out the cracked pan, slid in the new one and I was done!!!! No more unsightly crack!

My humidity control and veggie drawers were cracked and broken, I had shopped around but the price to replace them was too high and not in my budget. I came up on partselect.com while searching to find a more reasonable price. The price, service, delivery and customer service was outstanding. One of the drawer had been damaged during shipping, I called them and they sent another one free of charge right away. I had a very positive experience and I have added them to my favorite web sites.