MSD2542VEB00 Maytag Refrigerator - Instructions

Be gentle when installing new plastic crisper drawer. If possible, read install instructions in Refrigerator Owner Booklet. Put new crisper drawer in position and gently push in until you are stopped by encountering the "stops" in side-support rails that are attached permanently to walls of refrigerator. Per Owner Booklet, lift new crisper drawer up slightly to pass over the "stops", then let the crisper drawer settle back down and push it in the rest of the way. Removal is reverse procedure. Be gentle!

I first ordered an inlet valve. It arrived EARLIER THAN PROMISED. I then went back online to check for installation tips. While reading tips for installing the inlet valve I read that the Ice Maker Controller accounts for 48% of failures. I performed the simple test you recommended by connecting the wires from the water dispenser coil to the inlet valve coil to determine if the inlet vale is working correctly. Sure enough, the valve allowed water to go to the ice maker. I immediately went back online and ordered a controller. The controller took about 30 minutes to install.

I took the ice bin and crusher down to find the problem. I needed a new auger. I did a Google search for the part and found instructions for taking the crusher mechanism apart. This went smoothly until I went to put it back together. I had to follow the instructions in reverse which was really difficult. I advise folks to use their cell phone camera to take close up pictures of the dismantling process . Use these to help you put it back together. All in all, I was very pleased and plan to return when another need arises. John (retired x 2)

Just like the video I watched online at your web site. piece of cake.!!

The water inlet valve was easy to replace. Just like the video shows. With one exception. I found the two metal brackets were tough to get apart because they were riveted together. So I took the drill with a 5/16 bit and drilled the rivet apart. It might have come apart without drilling but I was afraid of bending the brackets. You don't need to drill clear through both brackets. Just the clean the head of the rivet. It was quick and easy. The bit size is not important just so it is bigger than the rivet head.

If you have to push your door to close it and it doesn't close on its own, this is your fix. These door cams are two plastic pieces on the bottom hinge, one on the door and one on the bracket that goes to the body, that engage like a gear with only a couple of teeth. They are supposed to have raised teeth that engage to ride the door to a closed position when it is nearly closed. They are plastic and are made to wear down. To change, empty the door, then at the top of the door (i.e., looking down from above) unscrew two bolts that go to the hinge. The door then lifts off the bottom bracket. Put the door on a soft surface and unscrew the bolt that holds this cam. You can re-use the bolt. There is another cam bolted to the bracket that stays attached to the fridge. Change both cams at the same time. Reverse the process to re-install the door. Your door will close like new for under $10, in maybe 15-30 minutes.

Upon arrival I unpacked drawers and set in their location

take nutdriver remove back cover, remove screws holding valve, unhook lines, hook lines to new valve, reattach valve and bracket and cover . yhats it!

The disassembling and replacing the broken part went exactly as the directions.

When the new crisper drawer arrived, I pulled out the old one and slid in the new one in less than 5 minutes. We won't overlead the new crisper drawer. Thank you PartSelect. I saved about $25.00 ordering this part from you.

take out old crack shelf and install new

Unplugged the refrigerator then removed two vertical screws on the very back back of the control panel (the ones with the washers). Do not remove the four other vertical screws in the panel. The front plastic plate on control panel snaps off and there are two horizontal screws under the plate. Remove them and the control panel will drop down allowing access to the light switch. Unplug the two wires (one black and one white) from the old switch. Discard the old switch, snap the new one into place and reconnect the two wires. Snap the front plastic plate back into place, plug in the refrigerator and you are done! Problem solved with a new $16.00 switch and saved at least $75.00 or more from an appliance repair call. Thanks Part Select!

followed video instructions... only thing done differently was to tape crusher blades together before removing from shaft and added a drop of sewing machine oil to all screw sockets before replacing to reduce rusting and create greater ease of removal if further repairs needed

TURN OFF WATER (if not already). Cut (or disconnect filler tube at bottom). Remove faceplate from refrigerator ice/water dispenser area. Remove screw holding metal bracket that holds water tube at filler point. Held metal mounting bracelet and pulled old filler tube out. Fed new filler tube thru bottom (hole is located at bottom of left door at hinge). As tube came out at top, pulled length needed to mount to new mounting bracket. Remounted new bracket (with hose attached) with new screw. Reconnected tube at bottom water line connection. Turn on water.

checked the close and open switch on front door first