Models
>
MS1440WB
MS1440WB Maytag Microwave - Overview
Sections of the MS1440WB
[Viewing 4 of 4]Keep searches simple, eg. "belt" or "pump".
TRAY-COOKING;JVM-1860,GL
PartSelect #: PS4234940
Manufacturer #: DE74-00023A
If you discover that the glass cooking tray in your microwave is damaged, you may have to replace it to operate the microwave properly. The glass cooking tray connects to the turntable of the microwav...
$96.98
In Stock
Ceramic Fuse - 20 amp
PartSelect #: PS11747931
Manufacturer #: WPM0805101
This microwave fuse is just over an inch in length. It has a white ceramic center, and metal on either end. This is a twenty amp 250-volt fuse, and is used to power your microwave. If your microwave w...
$10.19
In Stock
Micro Switch
PartSelect #: PS11741686
Manufacturer #: WP3405-001034
This is a micro switch, which is also known as a door switch for your microwave. The main reason for needing to replace this part is if you are not getting heat to your appliance. The door switch is l...
$51.43
In Stock
Rectifier
PartSelect #: PS11738693
Manufacturer #: WP13091701
The rectifier (also known as a diode) provides the microwave with energy to cook food. If your appliance is not producing heat or not turning on it could be due to the breakdown of the rectifier. This...
$25.99
In Stock
Assembly GUIDE ROLLER;JES831
PartSelect #: PS4236203
Manufacturer #: DE92-90189S
The turntable tray support holds the turntable tray while allowing the tray to rotate.
$49.53
On Order
Questions And Answers for MS1440WB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the MS1440WB
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
microwave oven blew fuse
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th
... Read more
e help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.
.
Read less
Parts Used:
-
tad from tamarack, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
24 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light bulb burned out.
Found instruction on internet,
1. Remove anit-tampering screws with punch and hammer
2. Remove the rest of the screws
3. Removed cover
4. Remove burned out bulb and installed new one
5. INstalled cover
6. Installed screws including the anti tampering onces
7. Op tested unit.
Wife is happy.
1. Remove anit-tampering screws with punch and hammer
2. Remove the rest of the screws
3. Removed cover
4. Remove burned out bulb and installed new one
5. INstalled cover
6. Installed screws including the anti tampering onces
7. Op tested unit.
Wife is happy.
Parts Used:
-
Stephen from Cottonwood, AZ
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
16 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microve stopped working
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise
Parts Used:
-
Denice from Montgomery, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
12 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!