Models > MMV1153BAB > Instructions

MMV1153BAB Maytag Microwave - Instructions

All installation instructions for MMV1153BAB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MMV1153BAB
1-10 of 10
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My glass turntable had broke in my microwave.

  • Customer: Judith from Fowler OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 16 people found this instruction helpful
Only had to set the new turntable in place. I was very impressed by the quickness in receiving the part.

The microwave turntable stopped rotating.

  • Customer: Patricia from Santa Cruz CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
I ordered a new coupler and dropped it into the center hole, jiggled it until it fell into place, put the turntable back on the track, and voila, fixed! It was ridiculously easy.

Buzzing noise, no heating of food

  • Customer: Ted from Hudson NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Removed control panel, discharged HV capacitor. Removed old diode, tested to confirm failure. Replaced part. Other than the removal of the panel swapping the part was almost as easy as replacing a light bulb.

Both bulbs burned out at same time

  • Customer: JOHN C from NORTH BEACH MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 21 people found this instruction helpful
I r/r the bulb cover, I then removed the burned out bulbs w/ a rag in case they broke they wouldn't have cut my fingers. You turn the bulbs lefty loosy. Installation is just the reverse. Install each bulb and turn righty titey, just snug the bulbs into place. Replace Glass cover and insert one phillips screw in plate and re-tighten

Bought microwave and it had no hanging screws with it.

  • Customer: Elaine from Allison Park PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 16 people found this instruction helpful
Ordered part and screwed in. Part could not be found in hardware store even though it was just a long set of screws. Agent quickly identified part with model number of microwave and it was at my home the next morning for installation. Great service!

Light didn't work.

  • Customer: James from Chicago IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I opened the section with a phillips screwdriver, unscrewed the bad bulb and replaced it with the good bulb.

microwave acts like its working but won't heat.

  • Customer: Mike from Paso Robles CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Replaced the magnetron and diode. Microwave works prefect now.

Microwave would trip ac breaker

  • Customer: Steve from Hampshire IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It was a over the range microwave It had to be removed off the wall. Once down I removed the bottom plate and then removed the touch control panel. Per the instructions in the user manual tested the transformer it was ok. Next tested the capacitor it tested bad and also the diode tested bad. The parts were ordered from you. The parts installed easily. Reassembled the microwave and tested. Unit no longed tripped the AC breaker and worked heating some water. Installed the unit back above the range.

BROKEN GLASS TRAY FOR MICROWAVE

  • Customer: SUSAN from ALDEN NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
SET IT IN THE OVEN, WONDERFUL!!!!!

no power

  • Customer: Glenn from Pedricktown NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took THERMOSTAT;NT-101NA,250 out and put THERMOSTAT;NT-101NA,250 in so easy got the part in LESS 19 HRS
All Instructions for the MMV1153BAB
1-10 of 10