Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MMC5086AAQ

MMC5086AAQ Maytag Microwave - Overview

Get Parts and Repair Help for MMC5086AAQ

If you know the microwave repair part you need, you can browse the list of all parts on the MMC5086AAQ, or you can search by name or part description. You can also find your part by where it is located on the MMC5086AAQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your microwave. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$52.44

Door Interlock Switch Kit

This part is a genuine manufacturer door interlock switch kit, also known as primary micro switch or microwave switch kit, for a microwave. The function of this part is to sense wh...

Order within the next 3 hrs and your part ships today!
$24.48

Light Bulb

Sold individually.

Order within the next 3 hrs and your part ships today!
$46.87

Turntable Motor

This motor rotates the glass turntable in the microwave.

Order within the next 3 hrs and your part ships today!
$21.68

Rectifier

The rectifier (also known as a diode) provides the microwave with energy to cook food. If your appliance is not producing heat or not turning on it could be due to the breakdown of the rectifier. This part works with microwaves, microwave oven combos, and wall ovens. This is one of the most common parts to fail over time in a microwave. This part is just under 3-1/2 inches in length. It is a genuine OEM part that is shipped right from the manufacturer. Make sure to use the proper precautions before attempting this repair. Ensure the appliance is unplugged.

Order within the next 3 hrs and your part ships today!
$64.85

CAPACITOR-

The high-voltage capacitor is an electronic device that holds a charge of electricity in the high-voltage circuit of the microwave. The capacitor stores electricity similar to how ...

Order within the next 3 hrs and your part ships today!
$17.76

Door Latch Spring

Order within the next 3 hrs and your part ships today!
$5.36

Fuse - 15 Amp 250V

Order within the next 3 hrs and your part ships today!
$130.53

Magnetron

This part is used to generate microwave energy/heat.

Order within the next 3 hrs and your part ships today!
$29.20

Wave Guide Cover

This part guides the waves to the inside of the microwave to cook your food.

Order within the next 3 hrs and your part ships today!
$7.99

FOOT-BASE

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Microwave worked intermittently depending on how door was closed

  • Customer: Robert from Bainbridge Island, WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 62 of 73 people found this instruction helpful
Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and also took a while to ... read more

Close the door on the microwave, punch in the # nothing happened

  • Customer: Robert S. from Stafford, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 20 people found this instruction helpful
I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped. read more

Needed to push door up to run appliance.

  • Customer: J Patrick from Baltimore, MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 26 people found this instruction helpful
1. Removed cabinet screws (10-15?). 2. Removed cabinet. 3. Removed top interlock switch which actually was not defective. The press clip connection appeared as if it had been arcing for quite some time and the corrosion created resistance sufficient to prevent the current from getting through the switch. 4. Replaced switch anyway but broke plastic retaining ... read more