Models > MLXE62REW2

MLXE62REW2 Frigidaire Washer / Dryer Combo - Overview

Get Parts and Repair Help for MLXE62REW2

If you know the washer / dryer combo repair part you need, you can browse the list of all parts on the MLXE62REW2, or you can search by name or part description. You can also find your part by where it is located on the MLXE62REW2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer / dryer combo. We’ve also included any installation videos we have for MLXE62REW2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$18.32

Upper Drum Glide

Front upper felt glide pad with 3 nylon glides - includes adhesive.

$2.77

Drum Support Bearing

$24.18

Door Catch

$12.70

Drive V-Belt

This belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

$8.21

Thermal Limiter - Limit 220

This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 ...

$19.41

Lint Filter

This filter collects lint as it passes through the dryer vent.

$22.80

Front Lower Drum Seal

This part helps to keep the dryer running as quietly as possible.

$10.94

Multi-Rib Drum Belt

$17.91

Water Inlet Valve

This washing machine water inlet valve has two ports for water to enter.

$47.18

High Limit Thermostat

This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops by 70 degrees Fahrenheit.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum glide wore down and caused close to get stuck between drum and front panel.

  • Customer: William from Boise ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 163 of 228 people found this instruction helpful
Unpluged dryer. Removed the top of dryer by pushing in a retaining clip on both sides of the front lip with a screw driver. Remove the two screws on both sides of front panel. These screws are square head or phillips #2. Unplugged the wiring harness to front panel (make sure power has been disconnected). Support drum and lean front panel away from dryer ... read more

replace broken drive belt

  • Customer: rodney from fairfield bay AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 124 of 141 people found this instruction helpful
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run... read more

Thermal Limiter opened

  • Customer: Stephen from Newnan GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 134 of 184 people found this instruction helpful
Unplugged Dryer.
Opened top of Dryer, over the drum.
Removed Thermal Limiter.
Tested the Thermal Limiter - found it was open.
Checked all vents and exhaust tube for lint build-up.
Replaced Thermal Limiter.
Closed top of dryer.
Plugged Dryer back.
Tested Dryer - it works. read more