Models > MHE14RFB0 > Instructions

MHE14RFB0 Roper Microwave - Instructions

All installation instructions for MHE14RFB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MHE14RFB0
76-90 of 143
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dirty grease filter

  • Customer: Joseph from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Slide grease filter about 1/2 inch to right (or left) using the D-ring attached to one side and then pull down and out. Push charcoal filter frame slightly to rear and pry down from front. Install new charcoal and grease filters by reversing process. No tools - 5-minutes max!!

BROKEN MICROWAVE GLASS TURNTABLE

  • Customer: MICHELLE from BROOK IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
ALL I HAD TO DO WAS OPEN THE MICROWAVE DOOR AND PLACE THE TURNTABLE ON THE DESIGNATED GROOVES, WHA LAH IT FIT. I AM NOW BACK IN BUSINESS. THANKS TO PartSelect, I found my replacement, ordered and it was shipped in no time.

vent grill tabs broke off

  • Customer: KENNETH from ROGERSVILLE AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
took old vent grill and tabs off using phillip screwdriver. started putting new grill on and it wouldnt go on. got to looking and there are two more screws that you have to loosen up so the grill will go into place these two screws are between the two tabs at each end. caution do not over tighten the screws it will break the tabs. overall easy to install.

The vent grill was broken

  • Customer: Norma G. from Poinciana FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I remove the old broken Grill Vent by loosing two screws and just put the new one and adjusted with the same two screws.

The top vent grill tabs broke rendering it unusable

  • Customer: James from Anoka MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I simply removed the original 2 screws for the old grill, attached the new grill, fastened it with the original screws & It fit perfectly in less than 5 minutes time.

Glass tray shattered

  • Customer: Mouang from Sacramento CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Ordered the glass tray and installed it. Received the orderin about two days.

broken

  • Customer: Donald from Pompano Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
put the turntable in and had a Rum and Coke to celebrate. Your service was GREATTTTTT...

Grill was cracked (mounting tabs) some time ago by unknown source. Suggest during in warranty problem on fire hazard. Vent grill was falling off.

  • Customer: John from Mentor OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Unscrewed the remaining (2) screws that held the vent in place, placed the new grill in the tab loctators, and screwed it into place. Done...in less than 10 minutes. It took me 15 minutes to find my wife to show her what a nice job I did.

Old vent grill cracked

  • Customer: Christopher from Olympia WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First remove two screws on top of microwave. Pull off old vent grill. Finally line up new vent grill (bottom edge first) then snap into place. Replace two screws on top of microwave.

Our vent grill was cracked

  • Customer: Barbara from Kensington MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
This was a piece of cake! Less than 48 hours to get the part and 3 minutes to find and return the screwdriver and 3 to make the repair! I removed two screws, the old grill and then set the new grill in place and rescrewed the screws.

part of grill plastic became crystalized and cracked

  • Customer: Judy from Albany OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
First, the screws were removed that held the vent grill to take off grill. The new vent grill was then replaced in a very short time. No problems at all.

Broken Vent Grill

  • Customer: STEPHEN from RICHMOND VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the 2 screws holding the broken vent grill, placed the new one in place and put the 2 screws back in place. Took less than 5 minutes from opening package to replacing the grill.

Glass plate of Microwave missing from an in bulit microwave

  • Customer: Martin King from Silver City NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Glass plate arrived in less than two days. Placed the glass plate in Microwave and presto the microwave works like a charm.

glass turntable in microwave cracked in half while cooking

  • Customer: barbara from phoenixville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
submitted manufacturer info to website and voila! a new glass turntable arrived in 2 days. I don't do well with computers, my 23 yr. old daughter was impressed......couldn't be easier! thanx! will definitely revisit your site

Broken Vent Grill

  • Customer: Jaime from Melbourne FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed screws holding tabs from broken vent grill to microwave frame.

Carefully snapped new grill vent into slots on top of microwave and slid tabs into slots on top of the frame.

Replaced the two screws in the tabs.

Finished
All Instructions for the MHE14RFB0
76-90 of 143