Models > MH7140XFB0 > Instructions

MH7140XFB0 Whirlpool Microwave - Instructions

All installation instructions for MH7140XFB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MH7140XFB0
76-90 of 158
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Microwave Glass Turntable

  • Customer: MICHELLE from BROOK, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
All I had to do was open the microwave door and place the turntable on the designated grooves, wha lah it fit. I am now back in business. Thanks to partselect, I found my replacement, ordered and it was shipped in no time.

vent grill tabs broke off

  • Customer: KENNETH from ROGERSVILLE, AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
took old vent grill and tabs off using phillip screwdriver. started putting new grill on and it wouldnt go on. got to looking and there are two more screws that you have to loosen up so the grill will go into place these two screws are between the two tabs at each end. caution do not over tighten the screws it will break the tabs. overall easy to install.

broken

  • Customer: Donald from Pompano Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
put the turntable in and had a Rum and Coke to celebrate. Your service was GREATTTTTT...

The vent grill was broken

  • Customer: Norma G. from Poinciana, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I remove the old broken Grill Vent by loosing two screws and just put the new one and adjusted with the same two screws.

The top vent grill tabs broke rendering it unusable

  • Customer: James from Anoka, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I simply removed the original 2 screws for the old grill, attached the new grill, fastened it with the original screws & It fit perfectly in less than 5 minutes time.

Vent grille tabs were broken

  • Customer: Debbie from Tucson, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Replaced it with a new vent grill simply by screwing in on. It works and looks great.

The Vent grill on my microwave broke

  • Customer: Lori from Sonora, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I was in a panic as no one in our twon had this part. I found PartSelect online and ordered the part. I ordered this part at 4PM and the next day at 2PM the part was at my house. My husband spent 30 seconds screwing it back on and it looks like new. I can't say enough wonderful things about your Company and Customer Service!!! You're the BEST!!!

Plastic vent on microwave was cracked and would no longer stay on.

  • Customer: Shirley from Coconut Creek, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed the broken parts and screws and placed the new vent on and tightened screws. I am an 76 year old woman, so if I could do this, then anyone can! Surprisingly easy to install.

Microwave gill fasteners broke and would not stay in place.

  • Customer: Karolette from Virginia Beach, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Replaced grill and greese and charcoal filters.

vent grill broken at installation screw

  • Customer: Tim from Palm Harbor, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
old vent off screwed new in less than a minute

Thought filters should be changed after 5 years of use.

  • Customer: Chris from Boulder, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Used hands to slide filters sideways, till they could be pried out with screwdriver or bare hands. When new parts arrived, easily slide new filters into position. In hindsight, we did not need to replace grease filter. I was able to clean one of those with ordinary dish soap, warm water, and a brush.

Plastic tabs broke and the grille fell off.

  • Customer: DIANA from BORDEN, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed the screws holding the broken tabs and thought the new vent grille would click right into place. I had quite a bit of trouble getting all the tabs lined up to click into place, but was finally able to do it. Then I just used the old screws to secure the new grille.

Vent grill plastic parts broke off so it would fall off the mircrowave

  • Customer: Emma from Alexandria, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Took screws off of old vent grille and installed new one. Very easy except my old one was a shiny black grille and this one has a matte finish. Description did not say which but I am fine with the part.

Vent was Broken.

  • Customer: Tom from Missoula, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I, carefully, inserted the bottom tabs into the appropriate slots. I then rotated the vent piece up and into place under the top lip of the Microwave. Once positioned I installed the screws required to hold the piece in place. Very simple replacement. It gave me a chance to clean the grease behind the vent.

vent grille was knocked loosesomehow. allthe holes for the screws were broken

  • Customer: Benita from Port Orange, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed the screws from the damaged sections and replaced the new vent grille. Less than 5 minute fix, and saved me over a 100 dollars according to the quote I got. Thanks
All Instructions for the MH7140XFB0
76-90 of 158