Models > MH1150XMT0 > Instructions

MH1150XMT0 Whirlpool Microwave - Instructions

All installation instructions for MH1150XMT0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MH1150XMT0
76-90 of 187
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the door handle was broken and the casing for the door was broken.

  • Customer: Chris from Keller TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 16 of 48 people found this instruction helpful
The part arrived with a couple of the small clips that hold the glass in place broken and a poor glue job. After I re glued the glass the installation was easy.

The vent grill was broken

  • Customer: Norma G. from Poinciana FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I remove the old broken Grill Vent by loosing two screws and just put the new one and adjusted with the same two screws.

The top vent grill tabs broke rendering it unusable

  • Customer: James from Anoka MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I simply removed the original 2 screws for the old grill, attached the new grill, fastened it with the original screws & It fit perfectly in less than 5 minutes time.

BROKEN MICROWAVE GLASS TURNTABLE

  • Customer: MICHELLE from BROOK IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
ALL I HAD TO DO WAS OPEN THE MICROWAVE DOOR AND PLACE THE TURNTABLE ON THE DESIGNATED GROOVES, WHA LAH IT FIT. I AM NOW BACK IN BUSINESS. THANKS TO PartSelect, I found my replacement, ordered and it was shipped in no time.

vent grill tabs broke off

  • Customer: KENNETH from ROGERSVILLE AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
took old vent grill and tabs off using phillip screwdriver. started putting new grill on and it wouldnt go on. got to looking and there are two more screws that you have to loosen up so the grill will go into place these two screws are between the two tabs at each end. caution do not over tighten the screws it will break the tabs. overall easy to install.

Vent Grille Cracked and broke at top screws attached area.

  • Customer: Mary Jean from Elkridge MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Fitted the grille in place and tightened the screws to hold in place.

broken

  • Customer: Donald from Pompano Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
put the turntable in and had a Rum and Coke to celebrate. Your service was GREATTTTTT...

Glass tray shattered

  • Customer: Mouang from Sacramento CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Ordered the glass tray and installed it. Received the orderin about two days.

Vent Grille broke

  • Customer: Rodney from Midland MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I place the vent in the opening, put the screws in place, tightened the screws and viola.

broken tabs for the vent cover

  • Customer: tom from saint james MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the broken tabs with a screwdriver and snaped in the new cover replacing the screws once I had it in place. the entire job took less than 5 min.

Grille was not attached by previous contractor (they just leaned it in place) We were to clean up and ofcourse when it was touched to the floor it went.

  • Customer: Michael from Hebron MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Repair was very easy. We were more impressed with your selection and ordering process. Very quick as was needed for this job to be completed. Our customer was impressed that we found the part and that we were able to get it in so quickly. You helped us continue our professional service. Thank You

Glass plate of Microwave missing from an in bulit microwave

  • Customer: Martin King from Silver City NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Glass plate arrived in less than two days. Placed the glass plate in Microwave and presto the microwave works like a charm.

glass turntable in microwave cracked in half while cooking

  • Customer: barbara from phoenixville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
submitted manufacturer info to website and voila! a new glass turntable arrived in 2 days. I don't do well with computers, my 23 yr. old daughter was impressed......couldn't be easier! thanx! will definitely revisit your site

Broken Vent Grill

  • Customer: Jaime from Melbourne FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed screws holding tabs from broken vent grill to microwave frame.

Carefully snapped new grill vent into slots on top of microwave and slid tabs into slots on top of the frame.

Replaced the two screws in the tabs.

Finished

Vent grill wouldn't stay on. The clips broke.

  • Customer: Julia from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Take out the screws, broken pieces of clip, then put in the new vent grill, replace the screws. Done!
All Instructions for the MH1150XMT0
76-90 of 187