Models > MH1150XMT0 > Instructions

MH1150XMT0 Whirlpool Microwave - Instructions

All installation instructions for MH1150XMT0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MH1150XMT0
46-60 of 178
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the original part had fallen off and broke when it hit the floor.

  • Customer: John from Los Angeles CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Removed two screws to that held the old bracket. Installed new part and replaced the screws. Very simple. About 10 minutes. The part cost about $38.00. A repairman charged my neighbor 100 + dollars for the part and plus installation for the exact same thing. I highly recommend Partselect.

Vent grille was broken

  • Customer: Eugene from Tampa FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Removed the two screws hlolding the old vent in place. Discarded the old vent. Snapped the new vent in place and attached with the two screws previously removed.

the door handle was broken and the casing for the door was broken.

  • Customer: Chris from Keller TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 15 of 41 people found this instruction helpful
The part arrived with a couple of the small clips that hold the glass in place broken and a poor glue job. After I re glued the glass the installation was easy.

Microwave Turntable Won't Rotate

  • Customer: Steven from Sacramento CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 11 people found this instruction helpful
I turned off the power to the oven at the breaker. I then removed the side trim pieces by removing the screws located behind the lower oven door. I removed the plastic trim pieces above and below the microwave oven and removed the control panel and slid it into the opening above the microwave. I located the two screws securing the microwave into the frame and began sliding it out. I had to disconnect a small wiring harness and two wires from the microwave that were attached inside the opening above the microwave. The microwave section was the easily slid out, turned on it's side where the turntable motor was accessed by removing the access panel. I pulled the old motor, checked resistance and it matched the new motor. I then checked the old motor by applying 120V to it and it ran FINE! I thought I had the wrong part, but decided to install the new motor anyway. I did, secured the access panel and replaced the microwave in the frame. I reconnected the wires and secured the control panel and tested the microwave...and the turntable works!

Hood light wont work

  • Customer: Brandon from Vancouver WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 15 people found this instruction helpful
Turned power off. Removed all the screws from bottom removed socket and replaced

Door handle and panel cracked

  • Customer: Matthew from Avondale AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Other reviews said this was an hour long project and rather difficult. Quite the opposite, this was a very easy project. Pried the old panel off with a flat head screwdriver, removed the old door handle from the inside, replaced the new door panel and glass and snapped it back into place.

Broken vent Grille (plastic tabs snapped)

  • Customer: Aaron from Trumbull CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
All you have to do is unscrew the clamps, remove the broken plastic pieces of tabs, fit the new grille into the slots on the bottom and put the two screws through the clamps at the top.

tabs broken off old vent

  • Customer: JOHN from DELRAY BEACH FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
took off old and replaced with new.
2 minutes mostly looking for stool to stand on to remove and replace screws.

Replace the panel door

  • Customer: Lam from Anaheim CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
Searched on the internet for repair assistance and found YouTube video that helped alot.
Need to provide installation directions in the product.

Broke rotating plate, it fell off counter after being washed

  • Customer: Lois P from Morris IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
Opened door and put new plate in.

Placed order on Thursday evening and received Sat Am

part wasn't correct

  • Customer: Bob from Grand Rapids MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
The first part I had to send back because it wouldn't fit. You made it easy to return the wrong part. The replacement part also wasn't correct. I was able to modify it to work. Cut off the not needed tabs and screwed in. Thanks for having something that would work.

The grill broke when removing it to clean

  • Customer: Kathryn from Everett WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unscrewed two screws, fit the grill into place and screwed in two screws.

the tabs for the screws completly crumbled

  • Customer: Kathleen from San Jose CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I removed the two screws, removed the broken grill, popped in the new grill (after I ordered the correct color, did not get the biscuit color I thought I had ordered the first time) replaced the two screws....I was good to go. Strange that the tabs in the first place just fell apart...but reading others, find this seems to be a common problem. Simple as pie.

BURNT OUT LIGHT BULB REPLACEMENT

  • Customer: alfred from summerville SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 16 people found this instruction helpful
OPEN COMPARTMENT, INSTALLED BULB, CLOSED COMPARTMENT

Broken Microwave Grill

  • Customer: Charles from Land o Lakes FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Placed Grill and tightened screws. It was trivial and the part was perfect.
All Instructions for the MH1150XMT0
46-60 of 178