Models > MH1150XMB0 > Instructions

MH1150XMB0 Whirlpool Microwave - Instructions

All installation instructions for MH1150XMB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MH1150XMB0
76-90 of 187
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Grill vent was broken

  • Customer: Daniel from Palm Bay FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
This is a very basic job that a ten-year-old can do. Simply remove two screws at the top of the unit, remove the broken pieces of grill, snap the new one in place, and replace the screws. Oh, yes, I also cleaned out the foam and aluminum filter and cleaned some of the grease from behind the filter.

Grille was not attached by previous contractor (they just leaned it in place) We were to clean up and ofcourse when it was touched to the floor it went.

  • Customer: Michael from Hebron MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Repair was very easy. We were more impressed with your selection and ordering process. Very quick as was needed for this job to be completed. Our customer was impressed that we found the part and that we were able to get it in so quickly. You helped us continue our professional service. Thank You

broken tabs for the vent cover

  • Customer: tom from saint james MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the broken tabs with a screwdriver and snaped in the new cover replacing the screws once I had it in place. the entire job took less than 5 min.

Vent Grille Cracked and broke at top screws attached area.

  • Customer: Mary Jean from Elkridge MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Fitted the grille in place and tightened the screws to hold in place.

Vent Grille broke

  • Customer: Rodney from Midland MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I place the vent in the opening, put the screws in place, tightened the screws and viola.

broken

  • Customer: Donald from Pompano Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
put the turntable in and had a Rum and Coke to celebrate. Your service was GREATTTTTT...

BROKEN MICROWAVE GLASS TURNTABLE

  • Customer: MICHELLE from BROOK IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
ALL I HAD TO DO WAS OPEN THE MICROWAVE DOOR AND PLACE THE TURNTABLE ON THE DESIGNATED GROOVES, WHA LAH IT FIT. I AM NOW BACK IN BUSINESS. THANKS TO PartSelect, I found my replacement, ordered and it was shipped in no time.

vent grill tabs broke off

  • Customer: KENNETH from ROGERSVILLE AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
took old vent grill and tabs off using phillip screwdriver. started putting new grill on and it wouldnt go on. got to looking and there are two more screws that you have to loosen up so the grill will go into place these two screws are between the two tabs at each end. caution do not over tighten the screws it will break the tabs. overall easy to install.

Glass tray shattered

  • Customer: Mouang from Sacramento CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Ordered the glass tray and installed it. Received the orderin about two days.

The vent grill was broken

  • Customer: Norma G. from Poinciana FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I remove the old broken Grill Vent by loosing two screws and just put the new one and adjusted with the same two screws.

The top vent grill tabs broke rendering it unusable

  • Customer: James from Anoka MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I simply removed the original 2 screws for the old grill, attached the new grill, fastened it with the original screws & It fit perfectly in less than 5 minutes time.

plastic holders broke on our vent grille

  • Customer: kristen from poynette WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
We took off the old grille - and simply screwed on the new one. Easy peasy.

The vent grille became lose and was falling off from the position each time we open the microwave.

  • Customer: Gloria from Middletown DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
First, I ordered the part.The part was sent to me within 2 days.Then,I removed the old one that was always falling off and mounted the new one. It was a perfect fit.

microwave vent grill

  • Customer: WALLEN from Anchorage AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I have been doing repair on things on my own for years, I am a retired prevenative maintenace supervisor.
While cleaning the microwave vent grill from being old it fell apart, so I ordered the part using the internet to find the a company that has the same part, the part didnt take long before I recieved it. It didnt take five minutes to install it, and it saved me cash in the pocket from someone else to do the work. wallen

Plastic vent on microwave was cracked and would no longer stay on.

  • Customer: Shirley from Coconut Creek FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed the broken parts and screws and placed the new vent on and tightened screws. I am an 76 year old woman, so if I could do this, then anyone can! Surprisingly easy to install.
All Instructions for the MH1150XMB0
76-90 of 187