Models > MGR5775QDS > Instructions

MGR5775QDS Maytag Range - Instructions

All installation instructions for MGR5775QDS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MGR5775QDS
211-225 of 227
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven wouldn't light sometimes, smelled gas

  • Customer: griff from gonzales LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed two screws from ignitor, pulled connector from hole behind it, replaced ignitor, reconnected. tried the oven and it worked first time. easy, easy.

Oven not heating.

  • Customer: Victor from Loxahatchee FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the racks inside the oven then (2) screws that hold the bottom cover. Once the cover was off I exposed the burner element. I Removed (2) small Philips screws that held the unit. I removed electrical plug and the unit was out. I replaced the part and put everything back together. This was a very simple job took me about 10 minutes to complete. gas company wanted to charge $130 just to come out and look at. I saved some good cash.

Oven not lighting /

  • Customer: Jack from Benicia CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed oven door and shelves and lower pan and replaced igniter

After the oven reached desired setting and turns off, the oven wouldn't relight.

  • Customer: RANDALL from Washington IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the sensor from the oven using a philip screw driver. The sensor was removed by removing the two screws holding it in place in the upper left hand corner of the oven. I had to disconnect the sensor on the back of stove. Then I pulled the old sensor through the hole inside the oven. Then I installed the new sensor by putting the wire of the sensor through the hole where the old sensor was removed. Then I hooked up the wire in the back of the stove. Then took the screw driver and replaced the two screws holding the sensor in place. It was very easy to do and the oven is doing fine now.

Heat sensor went out causing oven to shut down.

  • Customer: Stephen from Metairie LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.

oven would not heat up over 200

  • Customer: ricky from hollister CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
unplugged range took the oven racks out removed bottom plate, removed 2 screws from the igniter, wiggled the connector out of the hole, unplugged the connector. reconnected the connector reattached the igniter and put the plate and racks back in plugged the range in and it works just like it should. took about 15 mins. easier than I expected.

oven goes off like unplug no light no heat panel light come back on when oven get colder

  • Customer: boonsom from inglewood CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it

Broken inner glass

  • Customer: Joe from Bronx NY
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easy just loosened screws took apart door, removed broken glass and installed new glass.It took longer to clean the stove! Lol!

Gas smell and oven won't get hot, or takes too long.

  • Customer: Louis from Alpharetta GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I turned off the gas supply and unplugged the power source first. Then I removed the old igniter, by removing the plug wire clip from the back of the stove. I then removed the oven door by simply sliding it up and off the track. Once the oven door was removed I could easily access the igniter after removing the heat shield at the bottom of the stove. I had to remove two screws that mount the igniter. I had a little problem removing one screw, because it was stripped, so I had to use my Dremel tool to cut off the screw. Once it was removed the igniter was easily replaced with the new one. My wife and I was really excited that the fix worked! Saved me hundreds of dollars. Money I used for the holidays. Thanks Part Select!

Oven would not heat

  • Customer: Nick from Lockport IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced both the broiler (top) oven ignitor and bake (bottom) oven ignitor! Easy to do, no need to call a repair person on this job!

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

it was not the part i asked for the frame and plug didn't fit

  • Customer: Moshe from Brooklyn NY
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
i took out the new peace from the frame and i replaced into the old frame then i chopped the new plug also chopped off the old plug i connected the wires with electric tap then it got ready to plug in the new peace

Oven was not preheating properly and was not reaching the desired programmed temp

  • Customer: Donald from Florissant MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Fisrt, I removed the oven door by opening partially and lifting it up. It made it much easier to do the job. After removing the racks and bottom oven pan, I removed the two nuts holding the old igniter in place and then unplugged it from the wiring connector. Replaced the new one in the opposite order and BAM!, I was done. Five minutes, maybe...Nothing to it. I ordered the short oven sensor also, but didn't need it. Will just keep it on hand for possible future use.

Replacing a faulty temperature sensor

  • Customer: Marshall from Lakeland FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My first suggestion, after turning off the power to the unit, is to take the oven door off. Two simple screws and it's off! It makes getting to the temperature sensor much easier. I also moved the oven out so I could get access to the back to remove the rear panel. The ordered part came with two pigtails, neither of which fit my oven wiring harness. I cut one of them and the wiring from the faulty sensor, spliced them together with wire nuts and made my own connection harness. The new sensor went in with little effort. The wiring went together flawlessly with the spliced connection protected between the oven cavity and rear panel. Reattached the rear panel and the oven door, then slid the oven back into place. Turned on the electricity and back to normal! Problem resolved!!

The inner glass shattered when the oven was in the clean mode

  • Customer: Charles from Sulphur LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.
All Instructions for the MGR5775QDS
211-225 of 227