Models > MGC6536BDB > Instructions

MGC6536BDB Maytag Cooktop - Instructions

All installation instructions for MGC6536BDB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MGC6536BDB
1-15 of 30
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

top burners on stove won't ignite ,no clicking noise

  • Customer: scott from centreville VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 25 of 38 people found this instruction helpful
remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems.

spark igniter was weak and not lighting the flame.

  • Customer: Daniel from Needham MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 17 of 21 people found this instruction helpful
Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel and remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together.

Ignitor on main burner would not create a spark

  • Customer: Michael from Bloomington IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 16 of 24 people found this instruction helpful
Having no manual nor finding any instructions online, I spent a while trying to figure out how to safely get to the ignitor mounting screw under the range top. I popped the snap clips on either side of the stove to loosen the top and pulled the top up a few inches to see why it was being difficult to raise. It turns out that the gas piping was solidly attached from the controls to the burners and I was slightly bending the tubes as the top was raised. The tubes have angles and curves to "accept" the bending pressure I was applying, so it looked like I was doing the right thing. In case I was not doing the right thing, however, I raised the top only enough to get access to the ignitor base and mounting screw. Then the fun began as the screw would not loosen. After several attempts using liquid wrench, tapping on it, etc., the screw head finally just broke off. Uh-ohhhh. Not to worry, however, as there was an empty mounting hole right next to the old one that appeared to be able to work. The mounting screw for the new ignitor was backordered, so I tried a couple dozen different screws I had in my toolkit and finally found one that would fit width-wise, but I had to nip off some of the length to get it to seat properly. The replacement ignitor also had a different width blade connector than the original so I had to grind away some of its width to reattach it to the lead wire. If I had a different sized blade receiver, I would have instead replaced the receiver on the end of the lead wire. It took about 90 minutes in all.

grate feet missing

  • Customer: Jim from San Marcos CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 13 people found this instruction helpful
place new ones in by hand. the new ones fit too loose and if not carefull they will fall out.

Gas range would not light

  • Customer: Mike from Menlo Park CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
Replaced spark module but same problem persisted. Realized that the insulation on the spark ignitors were all cracked, causing a short.

Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.

Ordered new spark ignitors and plan to complete repair.

stovetop burner knobs were not snugly fitting on stove (metal inside part worn out).

  • Customer: Lin from Northridge CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
3 of the 4 burner knobs were broken. Finding the burner knobs on PartsSelect.com. was easy. What sold me on purchasing them were the pictures including a closeup of the back connection and the description of the make of appliance they'd fit. I ordered them Friday and they arrived the next day (standard shipping) on Saturday. Pretty amazing since I'd been putting it off for 6 months.

range burner igniter not functioning

  • Customer: Patrick from Greeneville TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 10 people found this instruction helpful
Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same

The shaft on the OEM knobs were cracked

  • Customer: Earnest from Pearland TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
Piece of cake. Knobs were slip on / slip off. Searched the Partselect website using the model number of the cooktop... presto.

Broken Knobs

  • Customer: Josph from Georgetown TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Removed old knobs and replaced with new knobs. Thank You

Knob extenders were cracked/broken

  • Customer: KarenLee from Coopersburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Simple as a dimple. Over time the plastic connections have gotten cracked or broken all together. Why they don't make them out of stainless is beyond me. Make more money, duh! Anyway, old off new ones one. Nothing else. This company speedy delivery - ordered Friday received Saturday. Thanks!

No spark at top burners

  • Customer: Joseph from East Freetown MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 12 people found this instruction helpful
Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

THe old burner knobs broke.

  • Customer: frank from woodstock GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
I simply took off the old knobs and replaced them with the new ones I ordered from you. They were exact replacements and cheaper than your competitors. You sent them quickly.
The experience can't be any better than that.
Frank

My repair was just a replacement of the burner knobs. I was cleaning the range top and removed the knobs to clean around it when it slipped and fell on my floor which is tile. Most items that hit it will break. A corner at the top of the knob was chipped.

  • Customer: Brenda from Shreveport LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I ordered a full replacement for the five knobs so that the other four wouldn't look like they were dull due to being older. Took less than a minute to replace the items.

I had a broken burner knob

  • Customer: Paul from Cambridge MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I simply took off the broken one and replaced it with the new one

broken knobs

  • Customer: Jon from Bellflower CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I pulled off the old and replaced with the new.
All Instructions for the MGC6536BDB
1-15 of 30