Models > MGC6430BDW > Instructions

MGC6430BDW Maytag Cooktop - Instructions

All installation instructions for MGC6430BDW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MGC6430BDW
16-22 of 22
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

spark igniter kept firing

  • Customer: fernando from santa fe NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced igniter switch assembly; slightly different connector in part provided had to be purchased separately and replaced for proper installation

old drip bowls needed replacement

  • Customer: scott from carrollton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repain involved removeing two screws in each of the burners. Easy to fix. Looks like new now for a fraction of the cost of replacement.

Rusty screws

  • Customer: Gerald from Melbourne FL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted screws it would be an easy job.

burner know had cracked.

  • Customer: Penny from Mansfield OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took old burner knob off by lifting it up & pushed on the new one. The new did not go down as far so I will be replacing all of them so it looks better.

burned out spark igniter

  • Customer: Janette from Gainesville FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

Gas explosion due to bad Gas Pressure Regulator

  • Customer: Charles from Buena Park CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
First step is to turn gas off to cook top and also disconnect power to the unit. Than using a crescent wrench disconnect the gas line going to the unit from the Regulator. Than again using the crescent wrench disconnect the regulator from the bottom of the unit. Next remove the nipple that connects the gas line to the regulator from the old unit. Apply new pipe dope to the threads and screw it into the new one and tighten down. Next install the regulator to the unit and install the gas line to the regulator. once done with the install you can now plug the unit in and turn on the gas. You are now ready to use the cook top again

range- top four burners will not light

  • Customer: Rick from Brockway PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed rear cover where the spark module was and change it
All Instructions for the MGC6430BDW
16-22 of 22