Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MGC5430ADQ

MGC5430ADQ Maytag Cooktop - Overview

Get Parts and Repair Help for MGC5430ADQ

If you know the cooktop repair part you need, you can browse the list of all parts on the MGC5430ADQ, or you can search by name or part description. You can also find your part by where it is located on the MGC5430ADQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your cooktop. We’ve also included any installation videos we have for MGC5430ADQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the MGC5430ADQ

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$16.50

Top Burner Igniter

This top burner igniter comes with a mounting bracket.

$53.00

Sealed Burner Cap with Electrode

This burner cap assembly is sold with the spark electrode. Please note this part has been redesigned and no longer requires a gasket. Sold individually.

$5.15

Screw

This screw is sold individually.

$6.90

Rubber Grommet

Used as the bottom feet of a gas stovetop grate. Sold individually.

$40.79

Burner Head Cap with Spark Electrode

This part distributes flame evenly to your cookware.

$74.98

Burner with Electrode

This sealed burner is used on some gas ranges and cooktops. This design does not require a burner cap. The burner electrode is also included with this item. No gasket seal required per manufacturer.

$96.50

Spark Module

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

$4.89

SCREW

Part might differ in appearance, but functions same as original. Sold individually.

$55.86

Burner Grate

This square burner grate has sides measuring is nine inches long. It is gray in color and is intended for use with Maytag brand gas ranges.

$81.28

Burner Head with Electrode

This sealed burner is used on some gas ranges and cooktops. This design does not require a burner cap. The burner electrode is also included with this item.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

A burner wouldn't spark strongly enough to light the gas.

  • Customer: Matthew from Brookfield, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 146 of 161 people found this instruction helpful
Replacement of these burners is very easy. You just twist the burner counterclockwise a quarter turn and pull it out. (You may need a big wrench if the range is very old.) Once out, just pull the two wires off and push them onto the new burner. Crimp them on with pliers if they're loose -- mine were. Twist the burner back on.
If the gasket under the bu... read more

gas burner ignitor failure

  • Customer: roy from East Providence, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 107 of 121 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt ha... read more

top burners on stove won't ignite ,no clicking noise

  • Customer: scott from centreville, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 37 of 55 people found this instruction helpful
remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems. read more