Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MFW9800TQ0 > Instructions

MFW9800TQ0 Maytag Washer - Instructions

All installation instructions for MFW9800TQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MFW9800TQ0
61-75 of 170
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The water didn't drain, so the drum wouldn't spin

  • Customer: Jill from New Rochelle, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.

F-20 Error Code

  • Customer: GARY from CLARKSVILLE, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 7 of 11 people found this instruction helpful
Take off top of washer and the flowmeter is in the back lefthand corner on the top of the washer. Replaced the water level switch on the top righthand of the machine also. Got about 150. 00 Total invested w/service call from local tech. F-20 has not came back yet. I hoped it fixed it washer is only 3 yrs. Old. -Gd

Baffle in washer tub broke off

  • Customer: MIKE from BENBROOK, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
Snaped new one in place and done.

washer not drain or spin

  • Customer: LAURA from SPARTA, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
it was a really easy fix. unclamped the 2 hoses and took out screw, removed water pump. Connected two hoses back and set in place then screwed in locking screw. could not have been any easier.

Following The Instructions Of The Repair Manuel,

  • Customer: gerard from arvada, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
First I removed the retainer ring and then pulled back enough of the boot to get the door switch out and plugged in the new switch put the retainer ring back on and it was finished. With out the repair book I would have been lost on how to do the job.

Shaft in water pump broke

  • Customer: Jeffrey from Adrian, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 5 of 6 people found this instruction helpful
I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.

baffle in tub fasteners broke, baffle disconnected from tub

  • Customer: Carl from Patterson, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
This part slides in and snaps in place, a 15 second job.

baffle connectors worn off

  • Customer: richard from chetek, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
Placed baffle inside of washer and pulled to lock into place. EASY!!!

Pump not draining the water out.

  • Customer: Martin from Kotzebue, AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.

Pump not working

  • Customer: Darrell from Lady Lake, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Replaced pump

Door latch failed and would not lock

  • Customer: David from Post Falls, ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 4 of 6 people found this instruction helpful
Took off bottom panel by removing 3 torx screws. Opened up door seal, removed three latch retaining screws, unplugged three wiring harnesses. Installed new latch and reinstalled in reverse order.

Baffle was worn out/broken

  • Customer: Day from Basking Ridge, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
No instructions needed. Very easy to replace. You guys are great! Much cheaper than others and delivered next day! You are now on my "favorites"!

door would not latch , and lights on front just flashed

  • Customer: FRANCIS from leesburg, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
1)I removed the bottom front panel,reached up the right side of the machine and pulled the manual release on the bottom of the latching mechanism.2)I then removed the top to the machine in order to gain access to the latch. 3)I removed three electrical connectors then the three mounting screws using a #15 Torx driver. I then reversed the reverse procedure to install the new latch. total time to do the job was less than half an hour. Machine works OK.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 9 of 22 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Door latch would not lock

  • Customer: William from Victorville, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
Removed 2 screws from rear of top that hold top of washer in place, lifted top at the rear and slid it back then lifted it off. Removed the three wiring harnesses from old switch, removed the three screws holding switch in place, theses are accessed from the door opening. removed the two lower screws first and held the switch from the top while removing the last screw. Placed new switch in place and started the top screw by hand followed by hand starting the remaining two screws, tightened screws with phillips screw driver, reconnected the three harnesses, reinstalled the top and secured with the two screws. Door locks and unlocks as it is supposed to.
All Instructions for the MFW9800TQ0
61-75 of 170