Models > MFI2568AEW12 > Instructions

MFI2568AEW12 Maytag Refrigerator - Instructions

All installation instructions for MFI2568AEW12 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MFI2568AEW12
16-30 of 522
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The side hinge broke off due to the door sticking. so it wasn't covered under warrant.

  • Customer: KEVIN from Battle Ground WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 14 of 15 people found this instruction helpful
first I removed the pantry drawer and the 2 crisper drawers. Then I removed the glass shelf and it's supports. Using a nut driver I removed the 2 screws holding the end cap to the side of the refrigerator. Carfully snaped the end cap loose of the clip in front and pulled it straight forward, being carful not to break the rear tabs holding the climate adjuster. I then removed the old climate adjuster from my broken part (it's held on by clips) and installed it on the new end cap. I put the new end cap in snapping it onto the existing clip and added the 2 screws. Put the shelf supports and glass back on top of the drawer, slid back in the crisper drawers, installed the divider into the drawer (it just slides in) then put the drawer back in and I was done. It was an easy job and I'm sure I saved at least one hundred dollors for 20 minutes work.

needed to replace filter

  • Customer: Marilynn from Holland MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 16 of 23 people found this instruction helpful
Turned old one until it snapped out. Replaced it with a turn.

replace plastic wheels on refridgerator

  • Customer: robert from oak forest IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 15 of 22 people found this instruction helpful
I used board levers to do one side at a time.Kinda tricky, but you can hoist up fridge high enough to replace wheels. take your time think it out and be safe . Make sure you use saftey boards to support load to protect yourself==good luck A small mirror may help to see how the rollers alien in the supports.

Lid to chef pantry would not work.

  • Customer: Rodger from Marion IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 12 of 13 people found this instruction helpful
First I removed the drawers and shelf above the pantry drawer and then removed the pantry drawer. The end cap came off very simply by removing two screws. I removed the slide attachment to the old end cap and attached it two the new end cap. I then installed the new end cap and replaced the drawers and shelf. The lid to the chef pantry popped right in place. Job complete.

The pin on the right side of the end cap broke off.

  • Customer: Clarence from Gold River CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 11 of 13 people found this instruction helpful
1. I had to remove the cold cut drawer.
2. Remove the two screws for the sliding track and then the sliding track.
4. Remove the two crisper drawers as well as the glass and the two supports for the glass.
3. Remove the two screws for the end cap. This is accomplished by gently lifting up at the front of the part. You will find another three parts that are attached to the end cap. One is the slider that controls the tempetature, it is attached to a long plastic rod that is connected to the back side of the end cap by pressure clip points. The other end of the plastic rod is connected to a piece that is mounted to the back wall of the refridgerator. this is removed by gently pulling the entire unit forward until it comes loose from the back wall. Once the entire assembly is removed, The plastic rod must be released from teh back of the end cap. This will allow both ends to be disconnected from the slider at the front and the piece that was attached to the back wall by rotating each end to allow the removal of the components fronm the end cap. Once everything is removed, you are ready to complete the repair by reversing the removal process.

Center rail broke AGAIN

  • Customer: Diane from Glendale AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 19 people found this instruction helpful
This is the 2nd time I had have had to replace the center rail in 2 years....

Refrigerator Control Switches not functioning

  • Customer: William from Richmond Hill GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 14 of 23 people found this instruction helpful
I removed and replaced the suspect Control board. The problem with the select switch not responding still existed. I then ordered a new “PS2371545 Dispenser Front Overlay – Black”. This cured all but one of the non responsive select switch problems. I notified PartSelect that I received a defective board and they promptly sent a replacement Overlay. This cured my problem. Thank you for your Help with my problem. I highly recommend your company. Bill S.

End cap pin broken

  • Customer: Emilio from Clinton MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 9 of 9 people found this instruction helpful
The end cap is a very easy job to remove. Removed the three screws that hold the end cap in place using a 1/4 drive socket. Removed sliding rail which is affix to end cap to be reused with new end cap. Installed new end cap with the three screws and your done very easy. What made the job possible was the ability to identify the part from the PartsSelect.com web site which has excellent parts identification catalog.

Hing on Deli Door broke off

  • Customer: Floyd from Jacksonville FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 8 of 8 people found this instruction helpful
Lifted out the glass shelf and then removed two screws to get the right side end cap off. This side has a mechanical slide to adjust the amount of cold air into the Deli area.

You will need to carefully remove the plastic slide linkage from it's guides so that you can turn it sideways and it will then come off the end cap.

If it wasn't for that minor slowdown it would be a five minute job.

Thanks to this web site for QUICKLY getting me the part and providing info on how to do the job.

CRISPER GLASS SHATTERED WHILE CLEANING

  • Customer: Thomas from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
Since it was apparent the crisper glass is fragile I was very careful to not stress it.
I opened the box then took a large board almost as big and slid it on.I carried both items to the fridge and with both doors open slid the glass into place.I am 65 yrs. old and have owned many refrigerators but this is a first. They don't build them like they use to..

The compressor would try to start,but would not.

  • Customer: Alfred from Port Charlotte FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 12 people found this instruction helpful
I pulled the whole unit(condenser&overload relay)
with my hand & disconnected the wire connected
to it & Replaced it with the new one.Peace of cake.

Wife dropped a gallon of milk on the lid and cracked the see through panel

  • Customer: Stanley from Gurley AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 7 people found this instruction helpful
Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid

Broken Bracket

  • Customer: Joe from Centreville VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 9 of 14 people found this instruction helpful
Remove (3) screws; Removed existing bracket and installed new bracket.

Great Service from PartSelect

no cooling either fridge or freezer

  • Customer: chad from stockton CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 7 of 8 people found this instruction helpful
Refrigerator was stored for about 2 years and we picked it up when the owner decided to move into an apartment and no longer needed to unit (lost home to foreclosure). Brought the unit home and it worked great for about 3 days. On the third day my wife noticed a slight electrical burning smell. I did also and quickly emptied the unit and hoped for the best. The unit did indeed stop working. I fancy myself a do it myselfer but I would normally not go near electricity but thought what the heck it was free if i ruin it I would give it away. After a little research i found Partselect and they had a great design and a few stories that sounded similar so i pulled the relay capacitor for the compressor and sure enough the unit showed burn marks where the unit had shorted out. Maybe a bug got in there or water, dirt but I ordered the part. I arrived in two days which was great. I installed the part and plug the unit in and crossed my fingers. Very happily the unit clicked on and has been running great ever since. thanks Partselect, while I may not be one of your big customers I will refer anyone with appliance issues to your site first.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 9 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
All Instructions for the MFI2568AEW12
16-30 of 522