Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MFI2568AEW Maytag > Instructions

MFI2568AEW Maytag Refrigerator - Instructions

All installation instructions for MFI2568AEW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MFI2568AEW
31-45 of 558
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Hing on Deli Door broke off

  • Customer: Floyd from Jacksonville, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 12 of 12 people found this instruction helpful
Lifted out the glass shelf and then removed two screws to get the right side end cap off. This side has a mechanical slide to adjust the amount of cold air into the Deli area.

You will need to carefully remove the plastic slide linkage from it's guides so that you can turn it sideways and it will then come off the end cap.

If it wasn't for that minor slowdown it would be a five minute job.

Thanks to this web site for QUICKLY getting me the part and providing info on how to do the job.

Crisper Glass Shattered While Cleaning

  • Customer: Thomas from San Diego, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 14 people found this instruction helpful
Since it was apparent the crisper glass is fragile I was very careful to not stress it. I opened the box then took a large board almost as big and slid it on. I carried both items to the fridge and with both doors open slid the glass into place. I am 65 yrs. Old and have owned many refrigerators but this is a first. They don't build them like they use to. .

No Problem, time to replace water filter

  • Customer: Ralph from Longmont, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 18 people found this instruction helpful
Turned the old one to unseat and replaced with a new one in the reverse order.

The compressor would try to start,but would not.

  • Customer: Alfred from Port Charlotte, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 15 people found this instruction helpful
I pulled the whole unit(condenser&overload relay)
with my hand & disconnected the wire connected
to it & Replaced it with the new one.Peace of cake.

Tab on end broke off allow crispers to fall off rail.

  • Customer: Ed from South Lebanon, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 11 people found this instruction helpful
lift glass, slide new rail in replace glass. 2 min repair.

the crisper cover which covers both crispers broke in a million pieces as i was cleaning it in my sink

  • Customer: dora ellen from winnemucca, NV
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 10 of 12 people found this instruction helpful
well, first, after calming down i removed the glass from my sink (this took a half hour). then i went to the computer and looked for jenn-air parts. the part-select site came up. the site was very easy to use and although i usually leave things like this for my husband to do i decided to order the part myself, which i did.
the trick was finding something on hand to cover the tops of the crispers which were both full of vegetables. i innovated and used a shallow broiler pan and its lid which covered 90% of both the crispers. the part came in five days unwrapping the part was easy, cleaned it with windex (no sink soaking this time) and inserted it on top of crispers............totally easy!!!!!

Parts broke due to overloading crisper trays

  • Customer: Joe from Richardson, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
Wife learned you can overload the cheese and fresh veggie trays and the plastic rails broke. Repair required removing parts from the old crisper frame -- no experience and no instructions. Had to study broken part and figure out how to remove parts. Released catches with a knife and, by trial and error, figured out how to install rescued components on new crisper frame with minor damage and frustration.

Left front plastic wheel was broken

  • Customer: mike from holly springs, NC
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 10 of 13 people found this instruction helpful
Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.

no cooling either fridge or freezer

  • Customer: chad from stockton, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 9 of 11 people found this instruction helpful
Refrigerator was stored for about 2 years and we picked it up when the owner decided to move into an apartment and no longer needed to unit (lost home to foreclosure). Brought the unit home and it worked great for about 3 days. On the third day my wife noticed a slight electrical burning smell. I did also and quickly emptied the unit and hoped for the best. The unit did indeed stop working. I fancy myself a do it myselfer but I would normally not go near electricity but thought what the heck it was free if i ruin it I would give it away. After a little research i found Partselect and they had a great design and a few stories that sounded similar so i pulled the relay capacitor for the compressor and sure enough the unit showed burn marks where the unit had shorted out. Maybe a bug got in there or water, dirt but I ordered the part. I arrived in two days which was great. I installed the part and plug the unit in and crossed my fingers. Very happily the unit clicked on and has been running great ever since. thanks Partselect, while I may not be one of your big customers I will refer anyone with appliance issues to your site first.

The door where the ice cubes drop out of the ice maker started flapping and all the lights on the front of the frig were blinking wildly. This happened at 3 am.

  • Customer: Jayne from Export, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 8 people found this instruction helpful
Did research on the internet, and learned that two capacitors on the main circuit board located on the back of the frig had gone bad. Tried to replace the two capacitors on the old board, but no success. So, I ordered the whole board and plugged it in. Only problem is new board is not programmed to frig. So, had to program frig. by following directions found on the internet. I saved at least $200. Thanks.

The LH End Cap hinge stud had broken...

  • Customer: Myrna from El Paso, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 8 people found this instruction helpful
Removed the crisper drawers (pull out, then up & out), remove the glass shelf above the "pantry", remove the pantry door (easy because hinge stud was broken), then remove the pantry drawer. Use 1/4" nut driver to remove the broken LH End Cap...it pulls up and out. With the phillips screwdriver, remove/replace the steel rail for the drawer action to the new part. Replace in reverse order (after your neat freak SO cleans everything!).

Compressor Locked up.

  • Customer: Edmond K. from Las Vegas, NV
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 36 of 92 people found this instruction helpful
This is not a repair Job for just any body to do unless you have had some Refrigeration training and some experience !

I have been Certified and Licensed on refrigeration systems small, large and very large
for the past 36 years

Drain pan failed and had many leaks

  • Customer: Malcolm from Parrish, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 14 of 26 people found this instruction helpful
Took two times getting the correct part, however after getting the correct part it took about 10-minutes to replace. Had to take the fan out. When you put the new drip pan in make sure it is positioned so that the guides on the pan aligns with slots in the bottom refrig brace, otherwise back pannel will not align correctly. The fan is very easy getting aligned in the new tray. May take a little effort. I do not know why the pan on a refrighterator that is less than 5-years old could start breaking into many pieces.

Compressor would not start

  • Customer: Rich from Monon, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 7 of 7 people found this instruction helpful
Removed back access cover with quarter inch nut driver, unplugged wire harness, pulled old relay out & plugged in new one, reconnected wire harness, and reinstalled access cover. Piece of cake. (Shipping was very quick) ***Frig was only 3yr an 1 mounth old.*** Maytag - Dependable Huh?

Six months in use time to replace the filter

  • Customer: Michael from Long Valley, NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 16 people found this instruction helpful
It is simple, unscrew the old screw in the new one.
All Instructions for the MFI2568AEW
31-45 of 558