MFI2568AES12 Maytag Refrigerator - Instructions

Unscrewed the old filter and screwed in the new one

One mnorning the temp on the frig was in the 50's and the freezer was cold. Tried to get someone to come out and repair with no luck. We purchased a new frig. Then I decided to see if I could repair the old one to use. I wish I had discovered partselect before I bought the new one. First I thought from the web site that it was a overload/relay problem so I ordered it and changed it out and it was very easy. Then that did not correct the problem so I checked further and discovered that it could be the defrost heat element and thermostat. On partselect web site I saw where if your coil is covered in ice that this could be the reason. I ordered them and watched the video of how to change them out. The video is a little misleading because chances are you will not have the room around the coil that it shows on the video and also the element and thermostat will not come as one unit as shown on the video. It is still easy to cut the wires ont he thermostat and install it. The heat element is a little tricky to get out and back in and the clips that holds yours might be a little different and more difficult to do than the video but you can do it. All in all I spent about 160. 00 And the frig is working like new.

Thanks to a very patient husband. He looked at the situation and methodically took the freezer drawer apart by trial and error and was able to replace the old shaft with the one we had ordered. We do not understand why this basic information is not in the manual or on the internet. It was relatively easy once we knew in what order to take the drawer apart.

I mistakenly ordered the wrong part the first time and it was too short. After calling and giving the model # they were able to order the correct part. Installing it was easy, it just dropped into place.

squeezed in the ends of the cover to insert the posts. It was very easy! But, be careful, don't over do it, line it up first!

installed new center rail part worked perfectly.

Removed the drawer. 2 Removed the crisper drawers. 3 Removed the glass shelf and metal supports for that 4 Removed the 2 screws that held the slide in place 5 Removed the 3 screws that held the end cap in place 6 Carefully removed the end cap and temperature regulator from the refrigerator 7 Carefully removed the drawer temperature regulator mechanism from the old slide. 8 Reversed the above instructions to replace everything.

Removed drawer and right side pantry end cap. Removed slide for drawer. Reattached slide to new pantry end cap. Reattached new pantry end cap. Replaced drawer. Very easy. Entire job less than 10 min.

I emptied the two drawers above the pantry shelf and the glass above the pantry drawer. removed the pantry drawer and the metal slide. took parts off the old side off and put them on the new. replaced the new part back into the ref. screwed it back in put the pantry drawer backin and the pantry door on. It took longer to replace the food items than fix the problem. Thank you for making it so easy.

Took out the old and slipped the new

Easy peasy, lemon squeasy. Remove the tray and two crisper drawers. Remove glass shelf. Remove 5 self tapping screws. Pull out old part and reverse to install new part. No hastles, no suprises except how quick and straightforward it went. PS good time to wipe out spills from fridge. Oh forgot, Snap in pantry door on hingepins

Piece of cake. Took out old filer and put in new one!

Problem: hinge is too fragile for the constant use it receives. However, repair is simple and, thanks to excellent prices at PartSelect, it is not a big deal to repair. Follow the excellent steps suggested by other contributors; they got it exactly correct.

Removed drawers and shelf from refrigerator. Removed left end cap from refrigerator 2 screws. Remove the metal slide from the end cap then attached it to the new end cap. Only 2 screws. Replace new end cap using two screws. Reassemble the drawers and shelf. Like new!

First off I had no idea how a fridge worked or where to begin and the troubleshooting section of the manual was a joke. So I took the back panel off made sure the coils underneath were clean. Took out the back panel of the freezer and made sure that nothing was frozen over and I hadn't seen excess water on the floor so ruled that out. I knew the condenser was still running so I took a shot in the dark. Ordered the part and waited for it to arrive. It took me 3 minutes to open the box and install it. Immediately knew it was working replaced the back panel and moved the fridge back.