Models > MFI2568AEB Maytag > Instructions

MFI2568AEB Maytag Refrigerator - Instructions

All installation instructions for MFI2568AEB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MFI2568AEB
46-60 of 573
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Tab on end broke off allow crispers to fall off rail.

  • Customer: Ed from South Lebanon OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
lift glass, slide new rail in replace glass. 2 min repair.

Drain pan failed and had many leaks

  • Customer: Malcolm from Parrish FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 9 of 16 people found this instruction helpful
Took two times getting the correct part, however after getting the correct part it took about 10-minutes to replace. Had to take the fan out. When you put the new drip pan in make sure it is positioned so that the guides on the pan aligns with slots in the bottom refrig brace, otherwise back pannel will not align correctly. The fan is very easy getting aligned in the new tray. May take a little effort. I do not know why the pan on a refrighterator that is less than 5-years old could start breaking into many pieces.

The orignal proberm was broken hinge on End Cap

  • Customer: David L. from Red Rock TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.

Broken refrigerator door handle

  • Customer: Renard from High Point NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 11 people found this instruction helpful
The handle is secured to screws in the refrigerator door by a sliding groove. So the old handle simply lifts up and off of the door. Similarly, I replaced the new handle by sliding it over the screws and down to secure it in place. The challenge was the screws and door panel were slightly bent from when the old handle broke, so I used the pliers and screwdriver to straighten them out enough for the new handle to slide on.

Compressor would not start

  • Customer: Rich from Monon IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
Removed back access cover with quarter inch nut driver, unplugged wire harness, pulled old relay out & plugged in new one, reconnected wire harness, and reinstalled access cover. Piece of cake. (Shipping was very quick) ***Frig was only 3yr an 1 mounth old.*** Maytag - Dependable Huh?

a piece broke off that caused a shelf lid to not open and close correctly.

  • Customer: Denise from Sammamish WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 6 of 8 people found this instruction helpful
It was a very simple operation and was done in no time.

Doing it myself saved me at least $100.00 or more.

I was very happy and satisfied with the part and how doing it myself saved me a lot of time and money.

Tab for deli cover broke off...after 1 year ordred part,

  • Customer: Cranson from San Francisco CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
Took off old cover 3 screws...removed metal track and 2 other plastic sliding bars for air flow..put on new cover and carefully put back deli cover on plastic pins..easy fix...lousy design by maytag again! Thanks to PartSelect easy and prompt service and delivery!

The threads on the yoke shaft stripped.

  • Customer: Steven from Crossville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 9 of 18 people found this instruction helpful
I had to cut off the old yoke since the threads had stripped and it would not come off. Once I did that all I had to do was to remove 4 screws on the auger motor and replace it with the new auger motor. Then I put the yoke on the new auger motor shaft and then put the unit back in the freezer. Work time was less than 15 minutes with no problems.

Lid kept popping off Pantry drawer

  • Customer: Alice from Santa Ana CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
Could not figure out why this was happening suddenly. Then remembered I had recently changed the lid to one I had stored for over two years in the garage. They had sent me a replacement lid when the unit was less than a year old because the origianl had a crack in the clear section. Noticed it seemed a little warped. Thought I would replace it to see if that solved the
problem.
We had to replace the side panel of the draawer because the warped lid had broken the peg off of one side. I didn't want that to happen again.
The new lid did the job....This company is the only one I will use in the future for my appliances. Very easy to find parts and the pricing was better.

Broken glass on pantry door

  • Customer: Michael from Roseville MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
Pulled the broken pantry door off, and snapped the new door in place. Vry simple.

Woke up and the front panel that tells the temp was off.

  • Customer: lisa from paulsboro NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Removed the back cover for the HV Board. Unplugged the cables from the old board, put the new board in the same exact way, connected the cables. Put the back cover back on. The hardest part was the programming. You may need to read it again in order to figure it out, but not too difficult. Face it there are only so many buttons, eventually you will go "AH-HA" ! I saved myself around $250! I will most definately use this site if I have other appliances that do not work! You guys rock!

~Lisa~

Broken tab that holds the pantry door on

  • Customer: Craig from Pueblo CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
I broke the left side end cap the holds the pantry door on.
I search the internet for the part and happened to run across part select. I order the part and received the part with in 3 business days. It took less than 30 minutes to replace the end cap.

The great reviews help me with my choice to order the part from part select. I will order parts from them again.

Thanks for helping me fix my fridge.

hinge pin broke off

  • Customer: eugene from kissimmee FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 4 people found this instruction helpful
take out two nut driver screws remove piece, take off track two philips head screws. transfer temp control rod, really easy then put track back on and install piece. probable took as long to remove the two veg crispers and glass top. this is a very easy fix. i did notice that the pin on the original was about 3/8 of an inch forward so flapper door did not quite line up and im sure caused the pin to snap off. the replacement part, the pin is exactly the same position as the other side. i believe the original was defective from the mfgr.

Light switch rocker broke, disabling freezer internal light, water dispenser, and ice dispenser

  • Customer: Kenneth from Newton Grove NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

The glass shattered in a 1000 pieces during a mild cleaning!

  • Customer: walter from crete IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
These guys had my part mailed in lighting fast! It arrived in 2 days in a padded box in perfect shape.The price was the best on line and they saved my life one day before thansgiving!! They got my vote and respect! Great job partselect!!! walt , crete illinois
All Instructions for the MFI2568AEB
46-60 of 573