Models > MFI2568AEB Maytag > Instructions

MFI2568AEB Maytag Refrigerator - Instructions

All installation instructions for MFI2568AEB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MFI2568AEB
496-510 of 545
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

I broke the post which the "deli door" pivots on

  • Customer: Wes from Toledo OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Undid two screws and replaced the broken part, very easy

Vegetable container Center Rail of my Maytag Refrigerator was broken. So I was facing difficulty to place the containers properly in position.

  • Customer: Mike from League City TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I bought the Center Rail and installed it as mentioned below:
1. Open both doors of the Refrigerator fully.
2. Take out the top glass of the box holder and keep it in a safe place.
3. Place one end of the new Center Rail on a slot located in the middle of the frame.
4. Slide the other end from any side and place it on the other slot.
5. Make sure that the entry side of the Center Rail should be in the front.
6. Now put back the glass on the top and it is ready to hold the vegetable container again.
7. Just role the vegetable container slide moving up and down so that the roller sets in Center Rail then push it.

Broken door switch and beverage door cracked

  • Customer: Jon from Whitefish MT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The beverage door was easy. Just pop out the old and in with the new. The light switch was just a small challenge. Getting the old one out was a little tricky using a putty knife, as directed, after a screwdriver wouldn't quite so it. Once out, the new switch hooked up and went in quite easily. Now, on to the icemaker, a bit more of a challenge.

Broken drawer tab

  • Customer: Monika from Sioux Falls SD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My 3 year old broke the tab, so I ordered the new piece. My husband installed it, but I was right there watching. Very simple fix. No issues at all. One thing I loved is that the shipping was super fast! I did not request any expedited shipping, but as fast as it came you would've thought I had. I know this is a website I will be purchasing future replacement products from!!

replaced water filter

  • Customer: james from kansas city MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
followed instructions on box

The pin on the pantry end cap broke so that the pantry lid was not functional.

  • Customer: Allen from Decatur GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the pantry end cap by first removing the pantry drawer. Then removing both crisper drawers and the first shelf with the plastic bars that hold it in place. Removed the slider that the pantry drawer rests on to move in and out -just needed a small flat head screwdriver for that. Then removed three nuts holding the end cap with a nut driver. End cap snap right out and new one went right in. Screwed in three nuts. Then reattached the slider for pantry draw with two screws. Reassembled shelf, crisper drawers and then slid in pantry drawer - reattached the pantry lid to the pins on either end cap. Very easy. The activity that took longest was acquiring the nut driver - I didn't have the right tool. All in all simple job.

pantry door hinge broke

  • Customer: John from Hiawatha KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
had to replace the whole right side panel, came off fairly easy, but to get the adustable rod out and back into the new panel was somewhat difficult. I found out you can bend more than what you think to get it out and back in. It is the rod that adjusts the air flow

Light in Freezer Compartment Out

  • Customer: William from Bath ME
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Changed bulb, not the problem, had to remove switch to identify correct choice to order (3 pronged verus 2) after that it was easy beyond having to stand on my head to make the exchange. (N B before removing old switch it actually came back to life)

Broken tab on end cap

  • Customer: steven from Townsend MT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Right part for the unit. A bit of a learning curve but like new.

broken glass in door.

  • Customer: Retta from Heber UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
popped out the old lid and put in the new one,great service and arrived quick.

The end cap had broken

  • Customer: Michelle from Pineville NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The little knob that holds the door onto the deli bin had snapped. I ordered the part, it arrived within a couple of days. I emptied the necessary shelves, cleaning as I went of course. Removed the old part and installed the new part- instructions weren't necessary. I had the part back in within a few minutes. Someone else had reported that it took longer to remove the shelves and replace them than it did to replace the end cap. I found my experience was the same. I was very proud that I didn't have to ask my husband to do the repair for me- I did it myself.

broken center rail ( second time)

  • Customer: GERALD from WILMINGTON NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply replaced broken middle drawer with new. Works fine

The water filter indicator kept blinking red.

  • Customer: Myra from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I opened the cover to the filter and screwed the filter counter clock wise until it came loose then removed the old filter and put the new one in. It was real easy.

Replace Pantry End Cap - Right Side

  • Customer: Lyman from Searcy AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
(Always pay attention to where parts are located and how you remove them.) 1) Remove vegetable and fruit drawers above the pantry. 2) Lift out the glass pantry top. 3) Remove the rails which support the glass pantry top and remove the pantry drawer. 4) Operate the temperature control lever on the end cap while observing the movement of the sliding vent covers just above the back of the pantry drawer. 5) Remove the 3 screws which secure the end cap. 6) Carefully pull the end cap away from the side of the cabinet, taking care not to break any of the attached pieces. 7) Remove the components that control the temperature of the pantry. Some must be rotated to bring the component through a slot (or similar arrangement) - the control arm snaps into a hole in the center back of the cabinet... so you may need to use a flat screwdriver to assist in freeing it. 7) Install the components just removed onto the new end cap. 8) Re-attach the control bar in the back of the cabinet. (Its other end is now attached to the new end cap.) 9) Position the end cap and secure it to the cabinet with the 3 screws. Before snugging them up, test them to insure that the temperature control is sliding correctly. 10) If all is well, snug up the screws. 11) Re-install the glass support rails, glass, pantry drawer and the veg and fruit drawers. 12) Place the left end of the front cover of the pantry drawer on the hinge pin on the left side. Carefully bow the cover to allow the right side to be slid over its hing pin on the right end cap. Job done. In the future, take care to insure that the pantry draw is pushed in and the cover is closed BEFORE you close either of the two doors on the refrigerator!

Right hinge broke when wife dropped a candy apple on the deli drawer lid.

  • Customer: James from Toano VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Couldn't have been easier. Remove the glass plate. The deli drawer lifts out of the slides. Two screws later, the entire assembly was out. Be careful with the adjustable vent that is attached to the right end cap. Gently pull out the end cap, the vent just has a tab on the very end that inserts into the rear wall of the fridge. After that, reverse for installation. JMC
All Instructions for the MFI2568AEB
496-510 of 545