Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MFD2560HES > Instructions

MFD2560HES Maytag Refrigerator - Instructions

All installation instructions for MFD2560HES parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MFD2560HES
961-975 of 1,038
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced broken door hinge

  • Customer: karen from monroe, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed items from frifge, took out the lower drawer, removed side plate with broken part by nutdrive, replaced it, and put everything back - about 15 minutes. Easy.

Broken pin

  • Customer: Teresa from Dothan, AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The right hand pin that holds the liftable clear door over the lowest drawer broke. It is a molded piece, so the whole right end cap had to be replaced. The large lower drawer, the two smaller drawers above it and the glass divider/shelf all had to be taken out. The end cap was removed using a 1/4" allen wrench hand driver, and the whole assembly had to be angle out at abour 45 degrees to release a connect temperature control slide from a slot in the back of the refrigerator (I was not expecting that, but it was not hard to free it). Several pieces had to be removed from the orginal end cap and placed in the same position on the new unit. I did this without looking at any instructions (of course), and it took a few minutes to figure out how to get it apart. Previewing instructions would not be a bad idea for those who don't want to figure out the puzzle. Reassembly was easy, and I then just reversed the process to put the fully assembled unit in its' place, put the drawers and shelf in and reattach the liftable door to the pin.

plastic tabs that hold pantry drawer to broke

  • Customer: Heidi from Helper, UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy to repair right side took a bit longer due to the temperature adjustment on that side.

Pin was broken

  • Customer: William from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed all three drawers and the glass shelves. Unscrewed the pantry end cap and disconnected the humidity control parts (no tools needed for this part) and installed them on the new part. Screwed the new end cap to the refrigerator and installed the glass shelf, the drawers and the lift up cover for the bottom drawer. This is a first for me to respond to a request for information on installation. I do so because I found the entire process easy, convenient, accurate and the part was delivered as promised. Thanks for a new "favorite".

Drawer lid tab broken

  • Customer: Matt from Federal way, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
It was very easy. Remove the lid and drawer. Remove the pantry end cap screws then remove the assembly. You will need to remove the long arm that controls the temp, take note as how it fits in the clips. Next, carefully twist the temp control, again taking note on how it came out. Assemble the same way in reverse, start with the control, then the arm, then screw it back into place.

Meat/Deli Drawer Tab Broke Off Had To Replace The Left Cap On Drawer.

  • Customer: GALE from JOHNSTON, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed drawers, screws and cap and replaced. Very easy and excellent service in shipping.

Right side of chefs pantry door broke

  • Customer: Susan from Howell, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Pretty easy to do except need to pay close attention to how the old part came off because the back was a little tricky. The part that hooks to the chefs pantry door and controls the temperature adjustment slide pay particular attention to. The whole job from start to finish about 30 minutes, definately would not hire someone to do, would do myself again.

Pantry end cap broke at lid hinge

  • Customer: Linda from San Luis Obispo, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This was sooo easy! Removed the vegetable bins and shelf. Then removed the the deli drawer and lid. Used a 1/4 inch nut driver to remove the three nuts. On kitchen counter, I removed the two cross-cut screws from slide rail and put it on the new piece. Replaced the three nuts on the new end cap and then the hard work began---clean the shelves and bins that had been removed and replace the food. My refrigerator looks like new!

deli drawer broken hinge

  • Customer: Bernadette from Moore, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Was very easy after I found right tool to get out the screws. There were only 3 popped old one out and put new one in. I waited over a year thinking this was a difficult/expensive repair. So not true...22$ and 15 min. I will definitely recommend this store/site and maintain it for my future use.

vegatable drawer wouldn't open

  • Customer: Joseph from Medford, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
had to replace side cap s because plastic pin sheared off

broken connection on deli door

  • Customer: marta from ooltewah, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
So easy! IDed the part with ease with the pictures.When the new part arrived, removed 2 screws from the old part and 2 nuts.Then removed old part and replaced with new part, which fit perfectly.Replaced screws and nuts, put the drawer and lid back on and done! I am a not very handy 58 year old female and this was easy.

Pantry door peg broke off

  • Customer: Mary from Waunakee, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the 2 veggie drawer, removed the meat /pantry drawer and shelf. unscrewed the screws, removed the end cap and replaced it with new end cap - screwed the screws back in and voila - DONE!

The small tab that holds the drawer lid in place (one on each side)

  • Customer: Ronald from Flemington, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the 2 bins, glass shelf, large drawer. Removed the 2 screws holding the right drawer slide. Removed the 2 screws holding the pantry end cap in place. Transfered all the parts from the old end cap to the new end cap and reinstalled the end cap. Replaced the slide, glass shelf and the drawers. Installed the large drawer cover (very carefully!) as this is what broke off last time. Total time start to finish about 30 minutes.

Pantry end cap hinge broken

  • Customer: William from Redding, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed shelves to allow access for removal of end cap. Remove three 1/4" drive screws and pull end cap forward to loosen and remove. The back assembly for temperature control of the bins will come out too. Remove temperature control rod and back assembly from end cap for reuse on new end cap. Remove two philips screws from drawer slider and detach from end cap. Reverse process for re-installation.

Replace the left side panel of the pantry draw.

  • Customer: Gaynell from Baton Rouge, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I first reviewed the video, paying attend to the order in which items were removed and put back in place. On the video, I noticed that the lid to the draw was put back into place before the draw. Following these instructions, the repair went extremely easy and fast. I would recommend reviewing the video first.
All Instructions for the MFD2560HES
961-975 of 1,038