Models > MFD2560HES > Instructions

MFD2560HES Maytag Refrigerator - Instructions

All installation instructions for MFD2560HES parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MFD2560HES
901-915 of 1,021
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

3 year old grandaughter closed the door without closing the pantry door first, subsaquently breaking off the tab that holds the pantry door in place.(right side end cap)

  • Customer: Charlie from Victorville CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed pantry slide out drawer, removed both upper drawers, removed glass shelf (below 2 drawers). Removed the front glass shelf support. It just sits in a grove, comes right off.Used a ratcheting screw driver,with no tip, to remove the screws holding the end cap. Disconnected the air flow adjusting lever from end cap.Cleaned the whole area with a sponge and soap and water.lol.( amazing how dirty it can get being out of sight). reinstalled the lever on the new end cap, screwed it in place, put everything back together, DONE!It took about 20 min, including cleaning.Oh yeah, had an "inservice" with my grandaughter on how to close the 'fridge door.

Deli Drawer Cover Broke Off

  • Customer: Heather from San Mateo CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The annoying cover to the deli drawer broke off again. This is my second time purchasing this part from this website (left side and now, right side). Both purchases were very easy. Replacing the left side is easier because there isn't a temperature adjuster to remove and reinstall. I found this website very easy to find my parts both times, and I installed the right side (the latest fix) in less than 15 mintues while taking care of two kids. Many women do repairs around the house and are successful! :)

Broken pin

  • Customer: Teresa from Dothan AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The right hand pin that holds the liftable clear door over the lowest drawer broke. It is a molded piece, so the whole right end cap had to be replaced. The large lower drawer, the two smaller drawers above it and the glass divider/shelf all had to be taken out. The end cap was removed using a 1/4" allen wrench hand driver, and the whole assembly had to be angle out at abour 45 degrees to release a connect temperature control slide from a slot in the back of the refrigerator (I was not expecting that, but it was not hard to free it). Several pieces had to be removed from the orginal end cap and placed in the same position on the new unit. I did this without looking at any instructions (of course), and it took a few minutes to figure out how to get it apart. Previewing instructions would not be a bad idea for those who don't want to figure out the puzzle. Reassembly was easy, and I then just reversed the process to put the fully assembled unit in its' place, put the drawers and shelf in and reattach the liftable door to the pin.

Broken hinge pin for deli drawer- right side

  • Customer: Bert from lake city FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The repair is staightforward. Simply remove the deli drawer (up and out), the glass lid, and the vegatable drawers above it (easier access- they just slide out). Using a 1/4 socket I removed the 3 screws holding the end cap in place. You then disconnect the 2-3 places where the end cap connects to the humidity adjustment (front and rear). When the end cap is out you have to remove the drawer slide as and humidity adjustment slide as it isn't included in the replacement part- just 3 more screws- same size). Attach the drawer slide to the new end cap and do everything in reverse to replace it. Took all of 20 minutes including cleaning/drying the drawers etc while I had them out. Easy project.

Replaced broken door hinge

  • Customer: karen from monroe GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed items from frifge, took out the lower drawer, removed side plate with broken part by nutdrive, replaced it, and put everything back - about 15 minutes. Easy.

"hinge" for the deli tray had broken off

  • Customer: STEVEN from ROCKLIN CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After one attempt to use super glue failed, obtained the part (shelf support). Had to remove drawers and a shelf to get to the support. Two hex screws held in place. No problems, a little touchy to put the lid back on, but all in all a simple repair. Didn't have instructions - didn't need them - it was straight forward.

Broken pin that holds the pantry flip door

  • Customer: Anthony from Donaldsonville LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed large lower drawer, removed contents from the lower shelf, removed the two produce drawers, removed glass shelf. At that point you will be able to remove the three screws from the left side pantry end cap. A slight upward and forward motion will release the side pantry end cap once the screws are removed. Once the side pantry end cap is removed, two screws will removed the drawer track. Note: you will have to slide the drawer track one way or the other to align a small hole to find and remove the hidden screws. The process was reversed to install the drawer track and side pantry end cap, etc. The actual removal and installation of the new side pantry end cap took less than 10 minutes. I was very pleased with the ease of ordering and speedy delivery of the part from PartSelect.com

plastic pin on left side end cap broke off

  • Customer: robert from Columbus OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the whole left side end cap. Biggest problem was taking out the trays. cleaning had to be done. Wow!refrigerators get dirty over time. The actual mechanical part was trival.

Pantry end cap broke at lid hinge

  • Customer: Linda from San Luis Obispo CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This was sooo easy! Removed the vegetable bins and shelf. Then removed the the deli drawer and lid. Used a 1/4 inch nut driver to remove the three nuts. On kitchen counter, I removed the two cross-cut screws from slide rail and put it on the new piece. Replaced the three nuts on the new end cap and then the hard work began---clean the shelves and bins that had been removed and replace the food. My refrigerator looks like new!

meat/deli drawer tab broke off had to replace the left cap on drawer.

  • Customer: GALE from JOHNSTON SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed drawers, screws and cap and replaced. Very easy and excellent service in shipping.

Broken end cap

  • Customer: Joesph from Medofrd MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed simple instructions as provided on web site. Part arrived within 2 days of ordering and installation was as easy as described. Will keep this web site handy for all future needs.

plastic tabs that hold pantry drawer to broke

  • Customer: Heidi from Helper UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easy to repair right side took a bit longer due to the temperature adjustment on that side.

Broken pin that holds Pantry lid. Left side pantry side.

  • Customer: David from PARADISE CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered part on PartSelect.com. Easy to find part from charts. Part deliverd quickly. Total time to install was 1/2 hour. 25 minutes of that time was cleaning the inside of the refrigerater while I took apart the pieces required to install the pantry side. Very easy...Only tools required was a nut driver and phillips screwdriver....30 minutes

Part of the pantry 4door hinge broke

  • Customer: JOHN from TRAVERSE CITY MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed stuff in bottom of fridge removed two hex head screws removed drawer slides reassembled in reverse order put stuff back in fridge Bought from Parts select because their graphics for identification of part needed much better then others

did not have the right size socket

  • Customer: Rosalie from Mystic CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
we only had mm sockets so had to go to the hardware store when we found they would not fit. We needed and american socket i/2 way between #6mm and #/7mm which turned out to be a 1/4 inch socket
All Instructions for the MFD2560HES
901-915 of 1,021