Models
>
MEX731CAS1
MEX731CAS1 General Electric Washer - Overview
Sections of the MEX731CAS1
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Drive Belt
PartSelect #: PS16542496
Manufacturer #: WE03X29897
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
$36.13
In Stock
Control Knob
PartSelect #: PS418888
Manufacturer #: 131858004
Sold individually. This white knob accepts a D-shaped shaft.
$43.78
In Stock
Front Upper Felt Seal with Adhesive
PartSelect #: PS832644
Manufacturer #: 5303937182
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so t...
$19.64
In Stock
Door Strike
PartSelect #: PS455020
Manufacturer #: 5303207102
The door strike is attached to the door of your dryer and holds the door closed. If your dryer door is not closing, this might be due to the door strike needing to be replaced. This is a simple repair...
$16.13
In Stock
Heater Assembly
PartSelect #: PS2378363
Manufacturer #: 131475320
This dryer heating assembly has 5/16" terminal on the housing.
$175.15
In Stock
DRYER LINT FILTER
PartSelect #: PS12741280
Manufacturer #: WE16X29397
This is the replacement lint filter for your dryer. The lint filter traps unwanted lint and debris so your dryer can effectively dry your clothes.
No Longer Available
Timer Knob - Dryer
PartSelect #: PS755794
Manufacturer #: WE01X10160
Used with washer/dryer combo machines. This knob takes a D-shaped shaft.
$74.44
In Stock
Tension Idler Pulley
PartSelect #: PS418897
Manufacturer #: 131862900
The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operatin...
No Longer Available
Washer Lid Lock with External Safety Switch
PartSelect #: PS648775
Manufacturer #: 134101800
Mounting bracket on this part replaces old style ( You may need to drill off old bracket before mounting new lock).
No Longer Available
IDLER ARM Assembly
PartSelect #: PS11775626
Manufacturer #: 5304507499
This idler pulley assembly is a manufacturer-approved replacement part for your washer/dryer. The assembly includes the idler pulley and arm. The idler pulley provides tension for the belt to rotate t...
$33.13
In Stock
Drain Pump
PartSelect #: PS271336
Manufacturer #: WH23X10016
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
No Longer Available
Questions And Answers for MEX731CAS1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jacques
March 14, 2020
When the washer is set for "cold water wash" no water enters the tub. I verified the water source: No kinks in the hose, disconnected the hose from the supply tab, opened the tap and cold water comes in. When the hot water tap is on, hot water enters the tub when set on "cold water". Is there a valve specifically controlling the "cold water" ? Do you have it available? At what cost? Do you ship to canada?
For model number MEX731CAS1
Hello Jacques, thank you for your inquiry. There is a water inlet valve that controls the water flow to the appliance (PartSelect number PS12337857). Unfortunately, this part has been discontinued at the manufacturing level, with no known replacement. We recommend contacting the manufacturer of your appliance directly to inquire as to what a replacement part number may be. We hope this helps.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the MEX731CAS1
[Viewing 11 of 11]Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drum belt broke
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on.
This was a first attempt ever at fixing an appliance and it was no big deal.
This was a first attempt ever at fixing an appliance and it was no big deal.
Parts Used:
-
Adrian from Middletown, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
184 of 264 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking washing machine; water would not shut off on fill up and rinse
Replacing the switch is relatively easy, however, I would caution all experiencing similar problems one thing. Before assuming, as I did, that the switch was bad, first remove the panel of the washer that houses the washing tub/basin. On the back of the tub, check to make sure that the tube connecting the tub and switch has not come off
... Read more
from the tub as it did in my situation. The solution to my problem of a leaking washing machine where the water would not stop filling on both wash and rinse cycles was simply reattaching the tube to the tub. If I would have checked that first, total job completion time would have been under 15 minutes. Hope this helps. If you need to replace the actual switch, remove the knobs, screws, and panel. Remove the wires, tube, and screw from the switch and reassemble new switch. That took me about 30-45 minutes.
Read less
Parts Used:
-
Aaron from Williamson, WV
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
91 of 102 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid Lock Assembly broke
The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would
... Read more
need to pay a repair person to do!
Read less
Parts Used:
-
Jenessa from Tacoma, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
74 of 92 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!