Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MERH752BAW

MERH752BAW Maytag Range - Overview

Get Parts and Repair Help for MERH752BAW

If you know the range repair part you need, you can browse the list of all parts on the MERH752BAW, or you can search by name or part description. You can also find your part by where it is located on the MERH752BAW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for MERH752BAW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.80

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$29.74

Long Oven Sensor

This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approximately 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.

$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$6.49

Levelling Leg

This is a levelling leg for your oven, range, or stove. It is just under 3 inches long, is all black in colour, and is made entirely out of plastic. The levelling legs on your oven allow your appliance to sit perfectly flat. The new one may be longer in length than your original, but will work the same. Install the new leveling leg, and test if you have it adjusted properly by putting the appliance on four legs. Adjust in or out as required if your oven is rocking. It is recommended to check the other three levelling legs on your appliance in case they are also damaged or worn.

$44.96

Door Gasket

The oven door gasket on your range functions as a seal between the warm interior of your oven, and the outside. It prevents heat from fleeing your oven when the door is closed. Bef...

$56.33

Bake Element

This bake element is found on the bottom of the oven.

$53.63

Oven Rack

This is a replacement oven rack and it is designed for use with ranges and ovens. This is a genuine OEM replacement part. The rack provides a level and stable surface for cookware ...

$33.97

Infinite Switch for Eight Inch Range Burner

This infinite switch is for 8-inch range burners. When an element is unable to produce any heat on a modern oven, the problem may lie with the infinite switch. This switch is responsible for sending power to the surface elements. Check the element and terminal block to ensure they are working properly. If they are in working order, check the infinite switch at the control panel for any wires that have overheated, or broken terminals to or from the infinite switch. If the infinite switch is damaged or malfunctioning, it will need to be replaced. Remember to unplug your range before beginning this repair.

$4.88

Screw

Sold individually.

$49.78

Broil Element

This broil element is found on the roof of the oven.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 120 of 139 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

Right rear burner went bad

  • Customer: Mark from Loxahatchee, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 114 of 124 people found this instruction helpful
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip char... read more

The Burner was getting too hot and you could not regular the tempature

  • Customer: Dennis from Hagerstown, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 55 of 61 people found this instruction helpful
Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one read more