Models > MER6772BAW

MER6772BAW Maytag Range - Overview

Get Parts and Repair Help for MER6772BAW

If you know the range repair part you need, you can browse the list of all parts on the MER6772BAW, or you can search by name or part description. You can also find your part by where it is located on the MER6772BAW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for MER6772BAW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$24.84

Lower Bake Element

This part is located in the lower oven at the bottom.

Order within the next 7 hrs and your part ships today!
$28.12

Long Oven Sensor

This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.

Order within the next 7 hrs and your part ships today!
$7.17

Levelling Leg

This leg is sold individually.

Order within the next 7 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 7 hrs and your part ships today!
$36.57

Broil Element - Push On Terminals

This broil element is found on the roof of the oven.

Order within the next 7 hrs and your part ships today!
$34.16

Upper Bake Element - 240V

This bake element is found on the bottom of the oven.

Order within the next 7 hrs and your part ships today!
$44.14

Oven Rack

Used in the lower oven. Sold individually.

Order within the next 7 hrs and your part ships today!
$76.23

Surface Element with Limiter - 6" - 1200W

Order within the next 7 hrs and your part ships today!
$32.77

Door Gasket

This oven door gasket comes with built in retaining clips.

Order within the next 7 hrs and your part ships today!
$37.07

Element Infinite Switch - 8"

This is the left front element switch.

Order within the next 7 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 85 of 97 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

Right rear burner went bad

  • Customer: Mark from Loxahatchee FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 73 of 80 people found this instruction helpful
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip char... read more

Upper broiler element (of upper over) burnt out

  • Customer: Todd from San Antonio TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 36 of 40 people found this instruction helpful
This particular model has a bracket that holds the element close to the oven ceiling, so I had to unscrew that as well as the element mounting screws on the back oven wall. The hardest part (not that hard) was the connectors were really tightly clamped to the element terminal. I had to use pliers to help wiggle them off the tips. Recommend doing this very... read more