MER6755AAS Maytag Range - Instructions

Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.

I went to your website and got the simple(even for me) Instructions on how to replace the element...you even had the part which I couldn't find anywhere else. Believe me I looked: searched the internet and looked locally...no luck. I then read the blogs of your customers and they all said the same thing...15 minutes or less to fix and a no brainer! Best of all I ordered the part late on Thursday and recieved it the afternoon on Friday in time for supper.

It's easier with two people.
1 - Turn the breaker for the range to OFF
2 - Verify power is off by testing the burners and lights
3 - Remove front two screws above oven door jamb
4 - Lift the top and prop it up with the spoon, or have your helper hold it.
5 - Loosen the screw at the rear of the bracket that holds the elements against the glass top (front and rear are held by the same retainer)
6 - Remove the bad element by sliding it sideways from the retainer. Do not disconnect things yet.
7 - The burner has numbers around the edge. Move brackets from old element to new one, matching the numbers. Then move wiring to new element. New burner may have a single connector where old one had 2 and a jumper. If so, ignore jumper.
8 - Slide new element under bracket and reinstall the screw.
9 - Lower the range top and re-install the screws.
10 - Turn on power and test.

Removed old gasket and replaced with new gasket'

Turned off the breaker to the oven. Removed the two screws, disconnected the element from the wires in the oven. Reversed the process to install the new element. But the best part was that the replcement element arrived in less than 24 hours from when I ordered it. Amazing

OMG you have no idea how grateful I am. My husband and I watched your how-to-video and decided that it looked pretty easy for us to replace on our own. We saved close to $200 between the flat fee for a service call plus labor. Thank you very much. We were also pleased how fast our part was shipped to us.

Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.

Shut off power at breaker box. Removed the door of the oven. It just lifts straight up. Removed 2 screws where the coil enters the back wall of the oven. Slowly pull the coil out and the wires will come with the coil. There is enough wire to pull the coil out a good 6 inches. You can then pull the connectors off the old coil and attach them to the new. Fish the wires back into the holes they came out of then line up the screw holes in the coil and tighten them up. Slip the door back on and restore the power.

turned off power to stove, removed two screws in rear of stove at element plate, removed two color coordinated terminals, hooked terminals up, installed two screws, and turned back on power.

It was really easy to replace the element. Remove two screws that holds in the element and pull it out about 3 inches. Remove the two wires and put in the new element. Plug in the 2 wires and screw it back in. It took about 10 minutes and the oven works great now!

removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

Disconnect the range from wall outlet. remove 2 screws in the back of the cabinet,remove switch plug. connect back range to outlet to check if it is the switch. make sure the light isn't on. then I order the switch online at PartSelect.com and it arrived in 2 days. When I installed the piece, the problem had been solved. I hope this information will be helpful for others.

The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!

unscrue 2 scroos remouved from the soccets and poot the new one