Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
temperature not accurate after 3 1/2 years of happy usage
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.
The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I turn it to 400 it slowly goes up to 425 degrees.
Took 2 screws under front edge of smooth top. Unscrewed ground wire from back of smooth top unit. Unplugged 2 wire bundles, from back. Took bad element out , put in new one. Put back together. About 10 min's tops. Easy peasy.
After reading many forums found that this error happens when trying to clean the oven and there is a failure in the latch motor to lock the oven door. It was suggested 1st to just tunr the breaker off to the over wait and then turn it back on to see if the error would clear by itself. If not then you'll have to do what I did and buy a new Latch Motor and replace it. Fairly easy to do: ) Move oven to get to the back panel ) Disconnect oven from power ) Remove the 8 screws to get the back panel off ) REmove the Latch motor screws (2) and remove the motor after twisting to get the latch rod off ) Put in new latch motor by 1st putting the latch rod in the motor assembly ) Screw the new motor in place ) Replace back panel ) Power on Oven DONE!
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
The broiler element started sparking and melting in one spot. I thought it would catch on fire and quickly turned off the oven.
First we unplugged the range. My husband removed the old element using a screw driver. He also removed the back panel on the oven after pulling it out from the wall. He unplugged the broiler prongs and plugged in the new element, put it all back together using the screw driver. We plugged it back in, turned on the oven and it is working great! Simple and easy to do in a short amount of time. Cool!!
Google the error code that the range was displaying and found others with the same symptoms. Then found several people that had fixed the problem by replacing the oven sensor. I then ordered the sensor and replaced it, which fixed the problem.
Very easy . Just removed four screws and removed the back cover. Then just unplugged two clips from the element . The repeated all of my steps in reverse . Be sure to unplug the oven before you start on the project .
Moved the stove out from the wall. Took out the screws from the back and then from the top. I pulled the piece through the back to unplug the clips from the elements. But the wires went back through the openings. So I had to take the back off of the stove to get to the wires to put back through the holes in the stove. Once the clips were back together, I put the back back on the stove. Rebolted the part to the stove and moved it back.
really easy! Removed 2 screws under the glass top at the front, access from the open oven door, then removed the ground wire, removed the stove top, took the element holder off,( 2 screws)and replaced with new element, 30 minutes. I ordered the part and came within 18 hrs of ordering it, fantastic experience.
To access the hidden bake element you have to remove the warmer drawer and the left side panel (your left from the back of the oven). To remove the side panel you need to access 3 screws under the side of the glass top, to lift the glass top open the oven door and remove 2 screws from the bottom side of the glass top. Once the drawer and side panel are removed you can use a flat head screwdriver to pry out the false bottom on the front side of the oven and remove 2 more screws on the side so it drops down. Move the insulation out of the way and relase the element tray by prying out 2 tabs on the front side. Unplug the connectors from the element terminals and remove the bolt holding the element. Fold the side of the element tray down to remove the element. Reverse order to install.
Turned off power.Removed 2 screws, flipped top over, removed old element, replaced new element,turned over top,fasten down with 2 screws.Turned on power. Turned on burner,made coffee-took a brake.
Remove top by opening oven and taking out two screws in the front. Lift up top and unplug wire connectors on bad element, writing down where they are landed. Take out screw on element bracket and replace. That easy. Be sure to unplug appliance for your safety. :-) Also just wanted to add that PartSelect was great. Ordered it on saturday and was cooking with it on tuesday. Great job.