Models > MER5770AAW > Instructions

MER5770AAW Maytag Range - Instructions

All installation instructions for MER5770AAW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MER5770AAW
31-45 of 267
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burner heat does not turn down

  • Customer: Gary from Blanchester OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

F1 code and oven wouldn't operate

  • Customer: Robbie from Hillsboro TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 6 of 8 people found this instruction helpful
I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

oven would shut-off, got an F1 code

  • Customer: Mike from Fairfax Station VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
I Goggled the default code of F1, my search stated that the temperature sensor might be bad. I bought one locally and installed it. I still received an F1 code, so I purchased this part called a "Clock, w/overlay" which is actually the control panel. It installed pretty easily, I took one wire off of the old control panel at a time and plugged them into the new panel, then put the rear panel back on. The oven heats normally now with no default codes.

the left front burner burned out & none of the lights to show if a burner was hot would come on.

  • Customer: Richard from Fair oaks Ranch TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 5 people found this instruction helpful
FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the counter.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.

Broken glass - oven door

  • Customer: Charles from Peoria IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
removed 5 trim screws from the perimeter of oven door, inserted new glass, reinstalled - done!

set oven to self clean and the inner glass broke

  • Customer: Garry from Livermore CA
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

My oven door handle broke

  • Customer: Dawn from Kingsley IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
I removed the screws from the top of the door, the sides and the bottom of the door. I still couldn't get the door to come apart because there were screws on the inside. It took me about 10 minutes to figure out that I had to slide the glass plate off the front of the door to get at the screws on the inside. Once that was done, I was able to replace the handle without problem. The only other thing is that I cut the top of my index finger while trying to clean the door before I put it back together. I was careful to keep track of which screws went where because otherwise it would get confusing. My handle looks and works great! Thanks

oven getting 50 degrees or more, hotter than setting

  • Customer: Joseph from Wappingers Falls NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

Oven kept shutting off, getting F-3, F-5 messages on LED readout

  • Customer: ken from north andover MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
I was out pricing new stoves. Why are slide in stoves twice the price of regular stoves?? I tried one last go at ordering part, overnight mail. Needed to get it fixed for the holiday meal. Part came within one day, early, and it worked. Stove fixed easily, spent the money on a big screen TV.

door glass broken

  • Customer: Mariano from Staten Island NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
My wife called a service company and was told that a tech would have to inspect the stove.
service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed the repair in 20 mins. Cost 89.00

glass pane was cracked during the cleaning process

  • Customer: Ellen from Shelton CT
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

My wife destroyed the oven door seal with oven cleaner...

  • Customer: David from Bexley OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its corresponding hole.

SMALL ELEMENT ON COUNTER TOP RANGE NOT HEATING.

  • Customer: Brian E from Waldorf MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 7 people found this instruction helpful
1. TURNED OFF POWER TO TROUBLE SHOOT THE COUNTER TOP RANGE ELEMENTS.
2.RAISED THE COUNTER TOP UP TO WORK ON IT AND SLID TWO EVENLY PLACED WOODEN SLATS UNDER THE BOTTOM OF THE HOUSFOR STABILITY SO IT WOULD NOT FALL BACKDOWN INTO THE COUNTER TOP CUT-OUT.
3. WITH A 1/4" NUT DRIVER REMOVED THE 10 HEX-HEAD SCREW THAT WERE HOLDING THE BLACK GLASS TOP IN PLACE, PULLED OFF THE 4 .CONTROL KNOBS AND CAREFULLY REMOVED THE GLASS COVER AND CAREFULLY SEET IT ASIDE IN A SAFE PLACE.
5. A VISUAL INSPECTION OF THE NON WORKING ELEMENT SHOWED THAT IT HAD A BURN OUT SPOT CAUSING IT NOT TO HEAT.
6. GOT THE MODEL NUMBER OF THE APPLIANCE AND CHECKED THE INTERNET FOR PARTS SUPPLIERS, CHOSE PARTS ELECT BECAUSE THEY HAD THE PART IN STOCK AND COULD OVERNIGHT IT FOR REINSTALLATION THE NEXT DAY, PART DID ARRIVE THE NEXT MORNING. A VISUAL INSPECTION SHOW THAT IT WAS THE CORRECT PART AND IT WOULD BE A LIKE FOR LIKE SWAP OUT.
7. PRIOR TO REPLACING THE ELEMENT CHECK TO SEE THAT THE ELECTRICAL POWER WAS STILL OFF AT THE CIRCUIT BREAKER, MADE A QUICK SKETCH OF THE WIRING AND IDENTIFIED THE WIRES SO THAT THEY WOULD BE RETERMINATED AT THE SAME POINTS.
8.USING THE NEEDLE NOSE PLIERS PULLED OFF THE 4 STAKE ON TERMINATIONS.
9. LIFTED OUT THE 6" FROM THE BODY OF THE UNIT , REMOVED THE 4 PHILLIPS SCREWS HOLDING PARTS WHAT WERE TO BE TRANSFERED ONTO THE NEW ELEMENT.
10. TRANSFERED PARTS ONTO THE NEW ELEMENT, REINSTALLED THE ELEMENT INTO THE BODY OF THE UNIT, REINSTALLED THE 4-STAKE-ON WIRES TO THERE APPROPRIATE TERMINALS AND VERIFIED WITH PREVIOUS WIRING SKETCH.
11. REINSTALLED THE GLASS TOP, 10 SCREW HOLDING IT IN PLACE AND THE 4-CONTROL KNOBS.
12 .TURNED MAIN POWER TO THE UNIT BACK ON AND TURNED ON THE REPLACED ELEMENT, IT WORK CORRECTLY, ALSO CHECKED THE OTHER 3 ELEMENTS TO MAKE SURE THAT THEY WERE WORKING CORRECTLY.
13. WHEN THE UNIT HAD COOLED, REMOVED THE WOODEN SLATS AND LOWERED THE COUNTER TOP BACK INTO ITS CUT-OUT MAKING SURE NOT TO DAMAGE THE GLASSTOP.
JOB COMPLETE.

oven wouldn't heat. Lower element only .

  • Customer: harry from chapel hill NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
First, I removed the two screws that hold the element in place. I then tried to pull the element out to disconnect the wires attached to the clips. The left side came right out. The right side would not. Had to pull the range out from the wall
(would only come out about a foot and a half due to the gas line connection). Removed the back (2 screws). Removed the clip from the element from the rear and redirected the wire into the oven. Replaced the back, pushed the oven back, attached the wire clip and screwed the element in place. Works fine. This is definitely a job not requiring an electrician.

Door Trim (bottom channel) had rusted due to a spill of tomato sauce down the front of the oven and into the channel.

  • Customer: G Lloyd from Cypress TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
The door trim is held in place by five (5) screws. First I removed the two (2) side screws and then the three bottom screws. Be very careful because the trim holds the front glass panel in place. The repair can be made without removing the front door of the oven. Just remove the bottom drawer to get to the bottom three screws. Took approx. 15 to 20 minutes to complete. That's because I took the time to clean the inside of the glass panel. Really easy!
All Instructions for the MER5770AAW
31-45 of 267