Models > MER5770AAW

MER5770AAW Maytag Range - Overview

Get Parts and Repair Help for MER5770AAW

If you know the range repair part you need, you can browse the list of all parts on the MER5770AAW, or you can search by name or part description. You can also find your part by where it is located on the MER5770AAW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for MER5770AAW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.58

Light Bulb - 40W

Sold individually.

Order within the next 6 hrs and your part ships today!
$27.04

Bake Element

This bake element has push-on terminal ends.

Order within the next 6 hrs and your part ships today!
$28.12

Long Oven Sensor

This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.

Order within the next 6 hrs and your part ships today!
$7.17

Levelling Leg

This leg is sold individually.

Order within the next 6 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 6 hrs and your part ships today!
$44.14

Oven Rack

Used in the lower oven. Sold individually.

Order within the next 6 hrs and your part ships today!
$32.77

Door Gasket

This oven door gasket comes with built in retaining clips.

Order within the next 6 hrs and your part ships today!
$37.07

Element Infinite Switch - 8"

This is the left front element switch.

Order within the next 6 hrs and your part ships today!
$4.05

SCREW

Sold individually.

Order within the next 6 hrs and your part ships today!
$2.70

Screw

Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an appliance to ensure an electrical connection is not lost.

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The element broke in two pieces after food dried on it.

  • Customer: Heather from Huntsville AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 93 of 96 people found this instruction helpful
First, I unplugged the oven. Then, I removed the two screws that hold the element in place. After that, I gently pulled the element toward the front of the oven until the wires were exposed. I disconnected the wires from the old element, removed the old element and then attached the wires to the new baking element. I gently pushed the new element back in... read more

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 85 of 97 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

F1-1 code

  • Customer: charles from marstons mills MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 34 of 40 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will ... read more