MER5730AAW Maytag Range - Instructions

removed the screws,pulled the element out about 3 inches disconnected the 2 wires

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

First thing- I cut off power to the range. I then removed two screws to allow the cook top to be lifted. I marked the wiring and replaced the burner. Reapplied power and started cooking!

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.

Piece of cake! Took more time to find the screwdriver than it did to replace the element!
Unplugged the stove. Removed 2 screws. Pulled the element out about 2" and disconnected the wires on each end (wires are attached to a metal clip that just pushes on to the end of the element. Threw the old element away. Unpacked the new elements. Connected the wires at each end. Pushed element into place and screwed in 2 screws. Plugged oven/stove back in and voila! That's it!

I had some confusion about the correct series number associated with my stove and called Partselect. They confirmed the part I was looking at was correct in less than 5 minutes. I then completed the order online. Even with standard shipping my order was processed immediately and I received the heating element the next day.

Turned off the breaker. Removed the two screws in the front holding the range top down. Loosened the screws holding the element in place while balancing the range top with my shoulder. Removed the wires from the older element one at a time and attached them to the new element. Put the new element in place and screwed back in place. If I had a little help with the range top I think I could have completed it in 5 minutes but I was at home alone and the other stories of doing this repair made it seem easy enough and it was.

I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.

Replaced screws and handle,pulled hinge's out to first stop and slid door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.

PS: shipping was fast and price was great.
Thanks Bob G.

Replacing the sensor kit and door gasket was no problem at all, however the baking element was A different story.
The problem was not the fault of the replacement part, but
the removal of the element to be replaced. The phillips head screws stripped out very easy and getting them out without damage to the interior finish of the oven was time consuming and challenging, but patients, and perservrance
win and so did I. Oven now works great

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

This was a complete no brainer. The easiest repair I have ever done. Take out the old screws, remove element and replace with new one, replace screws. Took less than 5 minutes :)

Unplugged the unit. Removed the back of the range and disconnected the top element connectors. Then removed the screws holding top element from inside the range. I did not remove the bottom rack so that my arm could rest on that rather than risk hitting the bottom element. Removed the top element and inserted new element. Placed the front bracket to hold element in place and tightend the two screws holding the element to the back of the range. Then reattached the connecting wires, replaced the back panel. Then completed attaching the braces holding element to top of range. Did not tighten braces until all screws had been started.

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

I removed the screws from the top of the door, the sides and the bottom of the door. I still couldn't get the door to come apart because there were screws on the inside. It took me about 10 minutes to figure out that I had to slide the glass plate off the front of the door to get at the screws on the inside. Once that was done, I was able to replace the handle without problem. The only other thing is that I cut the top of my index finger while trying to clean the door before I put it back together. I was careful to keep track of which screws went where because otherwise it would get confusing. My handle looks and works great! Thanks