Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDG9316AWW

MDG9316AWW Maytag Dryer - Overview

Get Parts and Repair Help for MDG9316AWW

If you know the dryer repair part you need, you can browse the list of all parts on the MDG9316AWW, or you can search by name or part description. You can also find your part by where it is located on the MDG9316AWW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for MDG9316AWW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$15.85

Drum Support Roller Kit

This drum support roller kit includes one drum roller and two bearings/washers. Most dryers use two drum rollers; it is recommended to change both at once. The drum support roller ...

$21.99

'M' Series New Style Coil Kit

This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils open the gas valve; if the valve does not open the heating element will not ignite. Both coils must be operational for the valve to open. This is a safety mechanism to ensure that there are no unsafe buildups of gas inside your appliance. This kit comes with a three-terminal boost/hold coil, and a two-terminal main coil. Each part is approximately 1 1/4 inches in diameter. If the igniter glows but shuts off without igniting gas, it means one of both of your valves is faulty. We recommend you replace these as a set. Before you begin this repair unplug your appliance and shut off the gas supply.

$4.71

Roller Shaft

This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller;...

$9.89

Front Glide Kit

The front glide is located at the front of the dryer and the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and may require replacing. This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. While you have the front bulk head removed for this repair, you may want to inspect the felt that lines it. If the felt is damaged, it is recommended that you replace it at the same time. You will need a rivet tool for this kit, as well as a stubby Phillips screwdriver, a 5/16 nut driver, and a drill with a 1/8-inch bit.

$14.56

Multi Rib Belt - 91-5/8"

At 91-5/8 inches in length, this dryer drum belt from Maytag has five ridges. It is all black in color and is made entirely of rubber. This flat belt is 3/8 of an inch wide.

$10.10

Idler Pulley Wheel and Bearing

This idler pulley wheel is white and made of plastic. It is two inches in diameter and comes with a center bearing.

$36.01

Lint Filter

This is a rectangle shaped lint filter screen used for some gas and electric clothes dryers. The dimensions of this lint filter screen are approximately twelve and a half inches lo...

$3.02

Retaining Ring

This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter. The retaining ring is a genuine OEM part sourced directly from the manufacturer. The ring may vary in appearance due to manufacturer substitution, but the function is the same. You may need to replace this part if the dryer is noisy during tumbling, will not tumble, or takes too long to dry. Be sure to check drum support roller kit and shaft before ordering parts.

$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor...

$29.36

Flat Style Igniter

This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lint into venting area.

  • Customer: Anthony from DeKalb, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 491 of 502 people found this instruction helpful
Removal of old lint collector and replace with new one. read more

dryer squeeking

  • Customer: gerald from park city, MT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 462 of 486 people found this instruction helpful
removed front panel,lifted top, removed drum and drive belt,remove old rollers and acc and instlled new and reinstalled dryer parts. read more

The old lint screen had a couple tears in it

  • Customer: Ron from Monte Vista, CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 373 of 377 people found this instruction helpful
No problem at all, just took out the old one in front and slid in the new one. read more