Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDE9206AYW > Instructions

MDE9206AYW Maytag Dryer - Instructions

All installation instructions for MDE9206AYW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDE9206AYW
481-495 of 628
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

roller noise

  • Customer: James from Arlington, TX
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I originally diagnosed as tension roller but found it to be a drum roller. Plastic had separated from the Babbitt bearing. So replaced both drum rollers and returned the tension roller. Only problem was the video was not for Maytag Neptune but a more generic dryer and I spent an extra hour try to reattach the drum belt. The video was the one that came with the email notification of part being shipped. Hook up to motor drive is backward from what the Neptune is. Eventually went looking for another video on my own and discovered the difference.

Rotating drum made an uneven louder whirring noise

  • Customer: Gary from Olathe, KS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I viewed the roller replacement instruction video on the website which was very helpful since I had never replaced drum rollers. A leisurely pace of one hour to replace the two rollers, half of which was spent vacuuming the interior. Removed the front panel without tipping the dryer. Had to disconnect a ground wire to remove one bracket but otherwise only had to remove screws, slip rings and washers. No belt removal. Drum was pulled away from rollers but remained in cavity Reassembled without any problem. Ran the dryer - much quieter and no longer had the whirring noise.

filter for dryer broke

  • Customer: john from fallbrook, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
put new one in

Dryer extremely noisy during operation - questionable whether drum was even turning

  • Customer: Clive from Saline, MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Googled repair video on You Tube to assess ease of repair. Disassembled dryer front and top. Removed and replaced the above parts as well as earlier order of drum slides and drum rollers. Checked motor was working prior to reassembly. Reassembled and everything worked well once used a couple of times to allow things to stabilize.

drum squeak, blower rattle

  • Customer: Tom from Shorewood, WI
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Cleaned and greased rear drum support rollers.Fine emory cloth on roller shafts. Replaced front support glide strips. Replaced blower, retaining ring and clamp.

no heat

  • Customer: Deborah from Hurricane, WV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
watched the u-tube video provided by you Part Select, very easy to follow, removed the thermostat and heating element as instructed, determined it was the thermostat and replaced it. The dryer works great. We saved alot of money thanks to Part Select.

Dryer not turning on.

  • Customer: Carl from Uncasville, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Researched the common problem with "dryer not turning on", and tested the top three problems. Removed the dryer front casing and door, unbolted front dryer plate. Used a volt meter on two of the temp gauges, which were fine. Removed the upper back plate of the dryer to the wiring for the knobs and buttons. Used the volt meter on the dryer start button, which was also fine. Went back around to the front and removed the door switch. Tested it with the volt meter and bingo. Replaced that part, dryer works like normal.

Timer dile broke

  • Customer: Lagina from Rutledge, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Snaped it on, lined up push,that simple

front glides kit worn out

  • Customer: stephen from fairfax, VT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first thing i did was look at the repair video 4 times. after that the replacement on of the guides were simple. thank you for suppling the video.

Belt worn out

  • Customer: gary from bono, AR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed old belt and installed new one by removing front panel and tub

Dryer stopped heating but still runs

  • Customer: MARK from Bedford, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
If your dryer does not run at all consider buying the thermal fuse with the tube. It is cheap and will save time if just the heater tube does not solve the problem.

1) Unplugged dryer.

2) Removed two screws on the front of the dryer panel under the door, swung bottom out and up to remove.

3) Removed one sheet metal screw in from of heater tube holding to base of unit.

4) Removed second sheet metal screw with nut driver that holds back of heater tube in to vent twoard back of dryer.

5) Carfully disconnected wires from heating element. and turn tube to gain access to screws on left and right sides of tube. Remove sub assemblies on sides of tube for thermal fuse. Just one screw for each, and they will lift off removeing tab from slot.

6) Vacumed out all oul lint.

7) Installed new heating tube by following above steps in revers order.

Tip, watch as you connect wires back on to tube. Make sure that they connect in the same place, and connect them in an order that will not interfear with re-assembly. I always take a picture with my cell phone before I disconnect anything, or draw a picture lableing wires and colors to positions. This job is very easy, and saves hundreds of dollars!!!

Loud squeaking on each start-up of the Dryer

  • Customer: Tommy from Vidor, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After watching the video on this web-site it was very easy. I took the time while I had the drum out to vacuum out everything inside the cabinet and sprayed the sealing felts with silicone spray before re-assembling the unit. Wallah!! No 'mo' squeaks. Tommy

Knob on washer broke during use.

  • Customer: chris from dubois, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Old knob had already fallen off. New knob arrived quickly and was a perfect match!! Great Job to the Part Select Team! Chris

Replaced Timer Knob

  • Customer: MARSHALL from ELLENWOOD, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simple old one cracked, popped new one on!

broken short baffle

  • Customer: Teresa from Acworth, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My husband, who normally calls a repairman for everything, followed the video and replaced the short baffle in less than 30 minutes from start to finish(this includes 2 or three trips up and down stairs to retrieve the right tools even though the video tells you the right tools to use). The part was identical to the original one and arrived in less than a week. Am very pleased with the whole process and am so thankful for the step by step video. The full repair was less than $30.00 for the part and my husbands time. I had been given a quote over the phone for this same repair of $250.00 to $375.00. Thank you so much and I will definitely buy from here again if it becomes necessary.
All Instructions for the MDE9206AYW
481-495 of 628